Panasonic NR-C45H1 / NR-D53H1 / NR-55D1 / NR-700D / NR-700M / NR-700MS / NR-700R Service Manual ▷ View online
---- 13 ----
C45H1, D53H1, D55D1,
D700D, D700M,
D700MS, D700R
D700D, D700M,
D700MS, D700R
DEFROST TIMER
STARTING RELAY AND OVERLOAD
PROTECTOR
PROTECTOR
Remove the screws (5 pcs) which fix the comp. cover.
Remove the comp. cover.
Remove the comp. cover.
Remove the clamp and the cover.
Unscrew screw (2pcs.).
Pull the connector downwards to remove.
Pushing the ribs (2portions), pull the timer box
Pull the connector downwards to remove.
Pushing the ribs (2portions), pull the timer box
rightwards.
Remove defrost timer, A.T bimetal thermo.
To replace the defrost timer
Be sure to set the timer in coolimg operation.
Rotating direction of cam shaft is counter-clockwise.
Rotating direction of cam shaft is counter-clockwise.
Pull the starting relay leftwards to remove.
Pushing both ends of clips inwards, pull up the overload
protector.
To replace the overload protector
The overload protector should be in the clip.
Install the protector to touch the compressor.
Rib
Relay cover
driver
Starting relay
Overload protector
Push inward
Clip
Rib
Screw
Screw
Defrost
Timer
Timer
Screw
Ac cord
assy
assy
Screw
Comp. Cover
(only Asia models)
Screw
Screw
Screw
---- 14 ----
C45H1, D53H1, D55D1,
D700D, D700M,
D700MS, D700R
D700D, D700M,
D700MS, D700R
Remove lamp cover
Remove screws (4 pcs), and pull the bottom part of
Remove screws (4 pcs), and pull the bottom part of
control plate.
Tear off the tapes on insulation.
Open the insulation from the front side pull the upper portion.
Remove the damper thermostat from insulation.
Disconnect the terminal.
Pull the ins. control panel as. & thermo. dial toward you.
Pull the ins. control panel as. & thermo. dial toward you.
REFRIGERANT FLOW DIAGRAM
Refrigerant flows in the refrigerating unit as shown in the figure.
Number in the figure of "PIPE LAYOUT" corresponds to number in the refrigerant flow diagram.
Number in the figure of "PIPE LAYOUT" corresponds to number in the refrigerant flow diagram.
To replace damper thermo.
Sealing dial should be put in place.
Seal the gap between the from insulation and the back
Seal the gap between the from insulation and the back
insulation by putting tape.
Hook the sensor bulb in place.
DAMPER THERMOSTAT
Screw
Screw
Ins. control panel
Terminal
Thermo. dial
Side Condenser
(Left)
(Left)
Side Condenser
(Right)
Mullion Dryer
Pipe
Pipe
Evaporator
Back Condenser
Capillary Tude
Compressor
Dryer
Control plate
Damper thermo.
Damper heater
SECTION V PARTS LOCATION
NR-C45H1
-15-
C45H1,D53H1,
D55D1,D700D,
D700M,D700MS,D700R
D55D1,D700D,
D700M,D700MS,D700R
124
124
155
155
NR-C45H1
-16-
C45H1,D53H1,
D55D1,D700D,
D700M,D700MS,D700R
D55D1,D700D,
D700M,D700MS,D700R
265
232
Click on the first or last page to see other NR-C45H1 / NR-D53H1 / NR-55D1 / NR-700D / NR-700M / NR-700MS / NR-700R service manuals if exist.