Panasonic NN-S650WF Service Manual ▷ View online
- 4 -
OPERATION AND DIGITAL PROGRAMMER CIRCUIT TEST PROCEDURE
1. Set the weight for 1 kg by press-
ing 1.0 kg pads.
2. Press Start Pad.
3. Press Stop/Reset Pad twice.
Oven shuts off.
8. When 2nd stage cooking time has
elapsed, oven beeps 5 times and
shuts off.
Time of day or colon if set appears
in the display.
3. Turbo Defrost
OPERATION
SCROLL DISPLAY
OPERATION
SCROLL DISPLAY
Time of day or colon if set appears
in the display.
9.23
1.0
2. Press Micro Power pad once
to set High power.
(1st stage)
3. Set for 5 seconds by pressing
pads.
4. Press Micro Power pad 4 times
to set Medium power.
(2nd stage)
5. Set for 1 minute by pressing
pads.
6. Press Start pad.
7. When 1st stage cooking time has
elapsed. Oven beeps twice and
automatically switches to 2nd
stage cooking.
OPERATION
SCROLL DISPLAY
1. Plug the power supply cord into
wall outlet.
2. Press Clock pad.
3. Enter time of day (TOD) by press-
ing appropriate pads.
4. Press Clock pad. TOD has now
been resistered into the digital
programmer circuit and will count
up by minutes.
2. Time Cooking for Two Stage
OPERATION
SCROLL DISPLAY
1. Place a water load in the oven.
8 8 . 8 8
1 1 2 5
1 1 : 2 5
1.0 0
P 1 0
. 5
P 5
. 5
1.0 0
1. To Set Clock
1. Press Vegetables pad twice to
select Vegetables for 2 servings.
2. Press Start pad.
When cooking time has elapsed,
Oven beeps 5 times and shuts off.
4. Auto Cook
OPERATION
SCROLL DISPLAY
200
6
10 1 10 1
10 1 10 1
10 1 10 1
2.30
Times of day or colon if set appears
in the display.
- 5 -
OPERATION
SCROLL DISPLAY
1. Press Auto Reheat pad twice
for two servings.
2. Press Start pad.Auto Reheat
cycle begins time counts down.
3.When cooking time has elapsed,
Oven beeps 5 times and shuts off.
3.30
Time of day or colon if set appears in
the display.
5. Auto Reheat
Press
Power Level
6. Power Level
Power Level
Display Window
once
twics
3 times
4 times
5 times
6 times
7 times
8 times
9 times
4 times
5 times
6 times
7 times
8 times
9 times
10 times
P 10 (HIGH)
P 9
P 8
P 7 (MED. HIGH)
P 6 (MEDIUM)
P 5
P 4
P 3
P 9
P 8
P 7 (MED. HIGH)
P 6 (MEDIUM)
P 5
P 4
P 3
(MEDIUM-LOW)
P 2
P 1 (LOW)
P 1 (LOW)
P 10
P 9
P 8
P 7
P 6
P 5
P 4
P 3
P 2
P 1
P 9
P 8
P 7
P 6
P 5
P 4
P 3
P 2
P 1
OPERATION
SCROLL DISPLAY
1. Press Start pad 3 times
continuously. “Child” appears in
the display.
Child
7. To set Child satety Lock
OPERATION
SCROLL DISPLAY
1. Press Start / Reset pad 3 times
continuously.
8. To Reset Child Lock
Time of day or colon if set appears in
the display.
400
V-16G-3C26
L-3C2-2
or
D3V
-16G-3C25
L-2C2-2
or
D3V
-1G-2C25
10 A
TMERMAL
CUTOUT
PRIMARY
LATCH
SWITCH
LATCH
SWITCH
AC240V
50Hz
50Hz
T
L
GREEN/BLACK
BROWN
BLUE
SCHEMATIC DIAGRAM
- 6 -
SCHEMATIC DIAGRAM
CAUTION:
HIGH VOLTAGE AREA
HIGH VOLTAGE AREA
HIGH VOLTAGE INVERTER
WIRING DIAGRAM
DESCRIPTION OF OPERATING SEQUENCE
1. Variable power cooking control
The coil of power relay B (RY1) is energized intermittently by the digital
programmer circuit, when the oven is set at any power selection except
for High power position. The digital programmer circuit controls the
ON-OFF time of power relay B contacts in order to vary the output
power of the microwave oven from ”Low” to “High” power. One
complete ON and OFF cycle of power relay B is 22 seconds. The
relation between indications on the control panel and the output of the
microwave oven is as shown in table.
NOTE: The ON/OFF time ratio does not correspond with the
percentage of microwave power since approximately 2 sec-
onds are required for heating of magnetron filament.
2. Inverter Power Supply Circuit NEW H,V
This Inverter Power Supply Circuit supplies 4,000V DC to the magnetron
tube from the line voltage, 220-240V 50Hz AC input. functions as the H.V.
transformer, the H.V.capacitor and H.V.Diode.
1. The AC input voLtage 220-240V 50Hz is rectified to DC voltage
immediately.
2. DC voltage will be supplied to the switching devices called IGBT. These
devices will be switched ON-OFF by the 20 to 40 kHz PWM. (pulse
width modulation) signal from the microcomputer in the DPC.
3. This drives the High voltage transformer to increase up to 2,000V AC
and approximately 3V AC by means of transformer.
4. Then the half-wave doubler voltage rectifier circuit, consisting of the
HV diodes and Capacitors, generates the necessary 4,000V DC
needed for the magnetron.
5. Output power of the magnetron tube is always monitored by the
signal output from the current transformer built into the inverter ciruit.
6. Then this signal will be fed back to the microcomputer in the DPC to
determine operating conditions and output necessary to control PWM
signal to the inverter Power Supply to control output power.
3. Inverter Turbo Defrost
When this Auto Control feature is selected and the Start Pad is tapped:
(A) The digital programer circuit determines the power level and cooking
time to complete cooking and indicates the operating state in the
display window. Table shows the corresponding cooking times for
respective serving by categories.
(B) When cooking time the display window has elapsed, the oven tums
off automatically by a control signal from the digital programmer circuit.
- 7 -
POWER SETTING
OUTPUT
POWER(%)
APPROX.
ON-OFF TIME OF
POWER RELAY B (RY1)
ON (SEC)
OFF (SEC)
HIGH
MEDIUM-HIGH
MEDIUM
MEDIUM-LOW
DEFROST
100%
90%
80%
70%
70%
60%
50%
50%
40%
30%
20%
20%
10%
30%
30%
22
22
22
22
22
22
22
22
22
17
11
11
6
17
0
0
0
0
0
0
0
0
0
5
11
16
5
Variable Power Cooking
P10
P9
P8
P8
P7
P6
P6
P5
P4
P3
P3
P2
P1
P1
P3
Inverter Turbo Defrost
SELECTED
WEIGHT
1.0KG
COOKING TIME
9 min.23 sec.
Click on the first or last page to see other NN-S650WF service manuals if exist.