Panasonic UF-8300 / UF-8200 / UF-7300 / UF-7200 (serv.man4) Service Manual ▷ View online
97
UF-7300/7200
UF-8300/8200
CN102
3.7.15. 2nd Feeder PC Board
CN600
CN601
LVPS
Pin No.
Signal Name
Destination
Signal Waveform
Function
CN102-1
ACL
Fuser Unit
AC Power Supply (Live)
CN102-3
ACN
Fuser Unit
AC Power Supply
(Neutral)
(Neutral)
2nd Feeder
PCB
Pin No.
Signal Name
Destination
Signal Waveform
Function
CN600-1
B
2nd Feeder
Motor-1
Motor-1
2nd Feeder Motor
Control Signal
Control Signal
CN600-2
AA
2nd Feeder
Motor-2
Motor-2
2nd Feeder Motor
Control Signal
Control Signal
CN600-3
+24VA
2nd Feeder
Motor-3
Motor-3
+24 VDC Power Supply
CN600-4
+24VA
2nd Feeder
Motor-4
Motor-4
+24 VDC Power Supply
CN600-5
BB
2nd Feeder
Motor-5
Motor-5
2nd Feeder Motor
Control Signal
Control Signal
CN600-6
A
2nd Feeder
Motor-6
Motor-6
2nd Feeder Motor
Control Signal
Control Signal
2nd Feeder
PCB
Pin No.
Signal Name
Destination
Signal Waveform
Function
CN601-1
PUSOL_CTL1 Pick Up
Solenoid-1
Pick Up Solenoid Control
AC120V
(AC200-240V)
AC120V
(AC200-240V)
+24V
0V
+24V
0V
+24V
0V
Sleep &
Shutdown
Shutdown
+24V
0V
Sleep &
Shutdown
Shutdown
+24V
0V
+24V
0V
+24V
0V
Pick Up
Solenoid
ON
Solenoid
ON
98
UF-7300/7200
UF-8300/8200
CN602
Refer to SPC PC Board CN724.
CN603
CN601-2
+24V
Pick Up
Solenoid-2
Solenoid-2
+24 VDC Power Supply
2nd Feeder
PCB
Pin No.
Signal Name
Destination
Signal Waveform
Function
CN603-1
LDJAMDOOR
-OP
-OP
JAM Cover
Sensor (2nd)-3
Sensor (2nd)-3
+1.2V
CN603-2
GND
JAM Cover
Sensor (2nd)-2
Sensor (2nd)-2
Ground
CN603-3
nJAMDOR-
OP
OP
JAM Cover
Sensor (2nd)-1
Sensor (2nd)-1
JAM Cover Sensor
detect Signal
detect Signal
CN603-4
LDPNON-OP No Paper Sensor
(2nd)-3
+1.2V
CN603-5
GND
No Paper Sensor
(2nd)-2
(2nd)-2
Ground
CN603-6
nPNON-OP
No Paper Sensor
(2nd)-1
(2nd)-1
No Paper Sensor detect
Signal
Signal
CN603-7
LDCCHK-OP Paper Tray detect
Sensor (2nd)-3
+1.2V
CN603-8
GND
Paper Tray detect
Sensor (2nd)-2
Sensor (2nd)-2
Ground
CN603-9
nCCHK-OP
Paper Tray detect
Sensor (2nd)-1
Sensor (2nd)-1
Paper Tray detect Signal
2nd Feeder
PCB
Pin No.
Signal Name
Destination
Signal Waveform
Function
+24V
0V
Sleep &
Shutdown
Shutdown
+1.2V
0V
+5V (H)
0V (L)
+1.2V
0V
+5V (H)
0V (L)
+1.2V
0V
+5V (H)
0V (L)
99
UF-7300/7200
UF-8300/8200
4 Troubleshooting
4.1.
Initial Troubleshooting Flowchart
START
Plug the Power Cord, and
turn the Power Switch ON.
turn the Power Switch ON.
Does the LCD display
function correctly?
function correctly?
Does the original document
feed through correctly?
feed through correctly?
Does the recording paper
exit the unit?
exit the unit?
Troubleshoot printed
copy quality problems
(Sect. 4.3).
copy quality problems
(Sect. 4.3).
Troubleshoot the
Document Feeder
(Sect. 4.4).
Document Feeder
(Sect. 4.4).
Check for recording
paper path problems.
paper path problems.
Troubleshoot Improper
LCD Display (Sect. 4.2).
LCD Display (Sect. 4.2).
Troubleshoot any 3-digit
INFO. CODE displayed.
INFO. CODE displayed.
Does the unit produce
normal copies?
normal copies?
Troubleshoot communication
problems (transmission,
reception, dialing, network
connection, polling,
information codes, or
diagnostic codes).
problems (transmission,
reception, dialing, network
connection, polling,
information codes, or
diagnostic codes).
Does the unit power up
normally?
normally?
Yes
Yes
Yes
Yes
No
No
No
No
Yes
No
100
UF-7300/7200
UF-8300/8200
4.2.
Improper LCD Display
• LCD Contrast Adjustment
1. Press the “FUNCTION”, “7” keys.
2. Select “8: MAINTENANCE?”, and press the “Set“ key to enter the Maintenance mode.
3. Select “6: LCD BRIGHTNESS?”, and press the “Set“ key.
4. Press the “ (Lighter)” key or “ (Darker)” key.
5. Press the “Set” key or the “Stop” key.
2. Select “8: MAINTENANCE?”, and press the “Set“ key to enter the Maintenance mode.
3. Select “6: LCD BRIGHTNESS?”, and press the “Set“ key.
4. Press the “ (Lighter)” key or “ (Darker)” key.
5. Press the “Set” key or the “Stop” key.
Replace the SC PCB.
Is the trouble
resolved?
resolved?
Replace the Low
Voltage Power
Supply Unit.
Voltage Power
Supply Unit.
Is the trouble resolved?
Check connectors on the SC PCB,
and PNL PCB.
and PNL PCB.
Is LED/LCD displayed?
Does the display appear normal?
Replace the LCD
Module.
Module.
Replace the
Panel.
Panel.
Does CNP501, pin 11 on the
SC PCB measure +5 VDC?
SC PCB measure +5 VDC?
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
START
END
END
Click on the first or last page to see other UF-8300 / UF-8200 / UF-7300 / UF-7200 (serv.man4) service manuals if exist.