Panasonic UF-8300 / UF-8200 / UF-7300 / UF-7200 (serv.man4) Service Manual ▷ View online
33
UF-7300/7200
UF-8300/8200
2 Disassembly Instructions
2.1.
General Disassembly Flowchart
Front Cover
2.3.1
EXT Cover
2.3.1
Rear Cover
2.3.1
Control Panel Unit
2.3.1
Top Cover
2.3.1
Fuser Unit
2.3.7
Bias Transfer Roller
2.3.9
Right Cover
2.3.1
Paper Feed Module
2.3.7
Paper Exit Sensor
2.3.7
Control Panel Unit
2.3.3
LSU Unit
2.3.6
SC PCB
2.3.4
MJR PCB
2.3.4
SPC PCB
2.3.4
LVPS
2.3.4
HVPS
2.3.4
Drive Unit
2.3.5
ADF Unit
2.3.2
Stamp Unit
2.3.2
Roller Assembly
2.3.2
34
UF-7300/7200
UF-8300/8200
2.2.
General Disassembly
Pertinent Disassembly Instruction sections are shown below.
Caution:
Reassembly is done in reverse order. Follow the instructions carefully, making sure that all parts are
properly installed to comply with EMI regulations and safety precautions.
properly installed to comply with EMI regulations and safety precautions.
Automatic Document
Feeder (ADF) Unit,
Scanner
2.3.2.
Control Panel Unit
Bias Transfer Roller
2.3.3.
2.3.9.
Paper Feed Module
2.3.8.
PC Board
2.3.4.
2nd Paper Feed
Module
2.3.10.
Cover Assembly
2.3.1.
LSU Unit
2.3.6.
Fuser Unit,
Paper Exit Sensor
Drive Unit
2.3.7.
2.3.5.
35
UF-7300/7200
UF-8300/8200
2.3.
Disassembly Instructions
2.3.1.
Cover Assembly
[1. Rear Cover]
(1) Remove 1 Screw, and the SD Card Cover (605).
(2) Remove 7 Screws.
(3) Remove the Rear Cover (604).
(2) Remove 7 Screws.
(3) Remove the Rear Cover (604).
Caution:
Remove the SD Memory Card if it was installed.
[2. Exit Cover]
(1) Remove the Rear Cover (604).
(Refer to 2.3.1. [1.Rear Cover])
(2) Remove 3 Screws.
(3) Remove the Exit Cover (602).
(3) Remove the Exit Cover (602).
Caution:
When reinstalling the Exit Cover, make sure 2 Latches
are fitted inside of the Inner Cover.
are fitted inside of the Inner Cover.
[3. Control Panel Unit]
(1) Remove the Rear Cover (604).
(Refer to 2.3.1. [1.Rear Cover])
(2) Remove the Exit Cover (602).
(Refer to 2.3.1. [2.Exit Cover])
(3) Open the Right Cover (614).
(4) Remove 2 Screws.
(5) Remove the Control Panel Unit.
(4) Remove 2 Screws.
(5) Remove the Control Panel Unit.
36
UF-7300/7200
UF-8300/8200
(6) Disconnect the Harness on the PNL1 PC Board
(CN230).
[4. Top Cover]
(1) Remove the Rear Cover (604).
(Refer to 2.3.1. [1.Rear Cover])
(2) Remove the Exit Cover (602).
(Refer to 2.3.1. [2.Exit Cover])
(3) Remove the Control Panel Unit.
(Refer to 2.3.1. [3.Control Panel Unit])
(4) Open the ADF Cover Assembly.
(5) Remove 3 Screws.
(6) Lift the ADF Tray Assembly.
(6) Lift the ADF Tray Assembly.
(7) Remove 2 Screws.
(8) Release the Latch Hook on the Top Cover (601).
(8) Release the Latch Hook on the Top Cover (601).
Click on the first or last page to see other UF-8300 / UF-8200 / UF-7300 / UF-7200 (serv.man4) service manuals if exist.