Panasonic UF-585 / UF-595 (serv.man2) Service Manual ▷ View online
Panasonic UF-585 / 595
36
2.13 Printer Cover (106), Rear Cover (105), Printer Motor (626)
(1) Remove the Left Cover and the Right Cover (Refer to
2.3).
(2) Release the hooks and remove the Printer Cover (106).
(3) 2 Screws (B1).
(4) Remove the Rear Cover (105).
(4) Remove the Rear Cover (105).
(5) Remove the HVPS Unit (424) (Refer to 2.12)
(6) 1 Screw (19).
(7) Remove the Ground Wire (542).
(8) Remove the Feed Roller Ground Spring (628).
(9) Remove the Connector on the Printer Motor.
(6) 1 Screw (19).
(7) Remove the Ground Wire (542).
(8) Remove the Feed Roller Ground Spring (628).
(9) Remove the Connector on the Printer Motor.
(10) 5 Screws (19).
(11) Remove the Motor Bracket (616) Assembly.
Caution:
The Gears underneath may dislodge when the Motor Bracket
is removed.
is removed.
(12) 2 Screws (4N).
(13) Remove the Printer Motor (626).
(13) Remove the Printer Motor (626).
(2)
(3)
(4)
(6)
(7)
(8)
(9)x5
(10)
(11)
(12)
Disassembly Instruction
37
2.14 LCU PC Board (402), Low Voltage Power Supply Unit (423)
(1) Remove the Rear Cover (105) (Refer to 2.13).
(2) Remove the Flat Cable from the Connector CN25 on the
(2) Remove the Flat Cable from the Connector CN25 on the
LCU PC Board.
(3) 3 Screws (B5).
(4) Remove the LCU PC Board (402).
(4) Remove the LCU PC Board (402).
(5) 1 Screw (B1).
(6) Remove the Parallel Port I/F Cover (113).
(7) 1 Screw (19).
(8) Remove the Right Printer I/F Bracket (406).
(9) 1 Screw (19).
(6) Remove the Parallel Port I/F Cover (113).
(7) 1 Screw (19).
(8) Remove the Right Printer I/F Bracket (406).
(9) 1 Screw (19).
(10) Remove the Left Printer I/F Bracket (405).
(11) 3 Screws (19).
(12) Remove the LVPS Protection Cover (404).
(13) Disconnect Connectors CN31 and CN33 on the LVPS Unit.
(14) 4 Screws (19).
(15) Remove the LVPS Unit (423).
(14) 4 Screws (19).
(15) Remove the LVPS Unit (423).
(2)
(4)
(2)
(3)
(4)
(2)
(4)
(2)
(4)
(8)
(5)
(7)
(6)
(9)
(10)
(11)
(12)
(15)
(13)
(13)
(14)x4
Panasonic UF-585 / 595
38
2.15 Fuser Unit (701), Thermistor Assembly (728)
CAUTION:
To prevent getting burned, do not install, remove, clean or adjust when the Fuser Unit is hot.
(1) Remove the Rear Cover (Refer to 2.13).
(2) 1 Screw (19).
(3) Remove the Fuser Top Cover (733).
(4) Disconnect Connectors CN85 and CN87 on the SNS4 PC
(2) 1 Screw (19).
(3) Remove the Fuser Top Cover (733).
(4) Disconnect Connectors CN85 and CN87 on the SNS4 PC
Board (729).
(5) Disconnect Connector CN31 on LVPS Unit (423).
(6) 1 Screw (4N).
(7) Remove the FG1 Harness (629).
(6) 1 Screw (4N).
(7) Remove the FG1 Harness (629).
(8) 4 Screws (19).
(9) Remove the Fuser Unit (701).
(9) Remove the Fuser Unit (701).
(10) Disconnect Connector CN86 on the SNS4 PC Board (729).
(11) 1 Screw (1Q).
(12) Remove the Thermistor Assembly (728).
Caution:
The Thermostat and Thermal Fuse are not available as Spare
Parts. If they become defective, replace the entire Fuser Unit.
Parts. If they become defective, replace the entire Fuser Unit.
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
Disassembly Instruction
39
2.16 Fuser Lamp (732), Exit Roller (719), Fuser Roller (709),
Pressure Roller (706)
(1) Remove the Rear Cover (Refer to 2.13) and the Fuser Unit
(Refer to 2.15).
(2) 1 Screw (4N).
(3) Remove the LVPS-Fuser Harness (727) and Fuser Lamp
(3) Remove the LVPS-Fuser Harness (727) and Fuser Lamp
Terminal B (731).
(4) Remove the Fuser Lamp (732).
Caution:
When reinstalling the Fuser Lamp, make sure that the Fuser
Lamp is inserted into the Fuser Unit as illustrated. Do not
touch the glass portion of the Fuser Lamp with bare hands.
Grease from fingerprints will shorten its life cycle, use isopro-
pyl alcohol to clean fingerprints.
Lamp is inserted into the Fuser Unit as illustrated. Do not
touch the glass portion of the Fuser Lamp with bare hands.
Grease from fingerprints will shorten its life cycle, use isopro-
pyl alcohol to clean fingerprints.
Caution:
When reinstalling the Fuser Lamp, make sure that both ends
of the Fuser Lamp fits into the projected area of the Fuser
Lamp Terminal A (724) and the Fuser Lamp Terminal B
(731).
of the Fuser Lamp fits into the projected area of the Fuser
Lamp Terminal A (724) and the Fuser Lamp Terminal B
(731).
(5) Remove the E22 Gear (722).
Caution:
You may need to use force to pull out the Gear.
(6) Remove the Right and Left P3.5L11.2 Bushings (720 and
721).
(7) Remove the Exit Roller (719).
(8) 2 Screws (4N).
(9) Remove the Fuser Cover (723).
(9) Remove the Fuser Cover (723).
(2)
(3)
(4)
White
Black
(6)
(7)
(5)
(8)
(9)
Click on the first or last page to see other UF-585 / UF-595 (serv.man2) service manuals if exist.