DOWNLOAD Panasonic UE-403162NA Service Manual ↓ Size: 819.52 KB | Pages: 49 in PDF or view online for FREE

29

360

-

-

Incomplete initialization for EP PCB.

EP PC Board incorrectly installed on the FCB PC Board.
FRM PC Board incorrectly installed on the EP PC Board.
PRT PC Board  incorrectly installed on the FCB PC Board.
Defective EP PC Board.
Defective FRM PC Board.
Defective PRT PC Board.
Defective FCB PC Board.

361

-

-

DPRAM (Dual Port RAM) initialization error 
on EP PCB.

EP PC Board incorrectly installed on the FCB PC Board.
FRM PC Board incorrectly installed on the EP PC Board.
Flash ROM on the FRM PC Board is blank. 
Defective EP PC Board.
Defective FRM PC Board.
Defective FCB PC Board.

362

-

-

Command Sequence Error.

Defective Printer Cable.
Software problem occurred. (FCB/FRM PCB)

There was an error writing to 
LPT1. The printer is not ready...

• Check if the Panafax facsimile unit is turned “On” and the printer cable is

properly connected.

There was an error writing to 
LPT1. A printer timeout error 
occurred...

• Check if the Panafax facsimile unit has paper.
• If the number of pages or quantity of data is exceedingly large, the

enhanced printer memory may become full and it will not be able to
received the print data. Increase the “Transmission retry” value in the
Details tab (Windows 95/98) or the Ports Tab (Windows NT 4.0) of the
printer driver Properties dialog box.

Cannot print because an error is 
found in the current printer 
setting.

• Verify and specify the paper size or orientation to coincide with the

application and the printer driver settings.

• The available page memory on the Panafax facsimile unit may not be

enough. Either install an Expansion D-RAM Card or change the
resolution to 300 dpi in the Printer Driver Properties dialog box.

• The Paper Size setting on the Panafax facsimile unit may be set

incorrectly (i.e. Installed A4 size paper but the setting is for Letter size
and specify to print a A4 size document). Check if the paper size is
properly set.

• Check if the Page Size setting specified in the document is coincide with

the setting in the Printer Driver Properties dialog box.

* PRINTING PC DATA *

Insufficient Memory

* PRINTER MODE *

WRONG PAPER SIZE

Specified an incorrect drive.

• Specify the correct Floppy disk drive.
• Make sure the Floppy disk is inserted properly.

Drive not ready.

• Insert the Floppy disk into the drive and click “Retry”.

There is a problem with either 
the Floppy disk or the Floppy 
disk drive.

• Make sure the Floppy disk is inserted properly.
• Try a different Floppy disk.
• Try the Floppy disk in a different PC.

30

32

Use the following procedure to change the function parameters.

The following buttons provide these functions in the test mode:
"START" : The new setting value is stored in the machine.
"\/"           : Scroll the function parameter number down.
"/\"           : Scroll the function parameter number up.

1

Standby

2

Press “FUNCTION” and then “7”.

3

Press “MONITOR” four times, then press “*”.

4

Press “1”.

5

Enter the Function Parameter Number.
Ex: Changing the "DC LOOP" -- Enter "009" and press [SET].

6

Press “START”.

7

Enter the new setting value.
Ex: Enter "2" for On.

8

Press “START”. The new value will be stored and the next parameter will be 
displayed.

9

Repeat steps 4 through 7 to change other Function Parameters or Press 
“STOP” twice to return to standby.

JUL-12-1999  15:00

00%

SET MODE        (1-6)

ENTER NO. OR

SERVICE MODE

ENTER NO. OR

PARAMETER (000-199)

ENTER PARAMETER #_

   PARAMETER   #009

DC LOOP?    

DC LOOP:Off

1:OFF 2:ON

DC LOOP:On

1:OFF 2:ON

   PARAMETER   #010

TX LEVEL?

JUL-12-1999  15:00

00%