DOWNLOAD Panasonic KX-MB263RU / KX-MB263UA Service Manual ↓ Size: 11.77 MB | Pages: 127 in PDF or view online for FREE

5

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that con-
tains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn),
Silver, (Ag), and Copper, (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.

• PbF solder has a melting point that is 50

° ~ 70° F, (30° ~ 40°C) higher than Pb solder. Please use a soldering iron with tempera-

ture control and adjust it to 700

° ± 20° F, (370° ± 10°C). In case of using high temperature soldering iron, please be careful not to

heat too long.

• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100

°F, (600°C).

• If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible and

be sure that any remaining is melted prior to applying the Pb solder.

• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the

opposite side (See figure, below).

There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufac-
turer’s specific instructions for the melting points of their products and any precautions for using their product with other 
materials. 
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

When discarding P. C. Board, delete all personal information such as telephone directory and caller list or scrap P. C. Board.

1. Unplug the power cord and short the two prongs of the plug with a jumper wire.
2. Turn on the power switch.
3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part

(screw heads, control shafts, bottom frame, etc.).
Note: Some exposed parts may be isolated from the chassis by design. These will read infinity.

6

4. If the measurement is outside the specified limits, there is a possibility of a shock hazard.

Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to following caution:

Disposal of lithium batteries should be performed by permitted, professional disposal firms knowledgeable in state government
federal and local hazardous materials and hazardous waste transportation and disposal requirements.
A battery continues to have no transportation limitations as long as it is separated to prevent short circuits and packed in strong
packaging.
Commercial firms that dispose of any quantity of lithium cells should have a mechanism in place to account for their ultimate dis-
position. This is a good practice for all types of commercial or industrial waste.

Recommend Type Number:
CR2354 (BAT300) Manufactured by MATSUSHITA

• The printer of this unit utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

• The fuser unit is inside of the unit and gets hot. Do not touch it when removing the jammed paper or cleaning the lower glass.

7

• Design and specifications are subject to change without notice.
• The pictures and illustrations in these instructions may vary slightly from the actual product.

Multi-Function printer

Max. 216 mm in width, Max. 297 mm in length

208 mm 

Letter/ Legal: 208 mm 
A4: 202 mm 

Copy resolution:
Up to 600 

× 600 dpi (Scanner Glass)

Scanning resolution:
Up to 600 

× 1200 dpi (Optical)

Up to 9600 

× 9600 dpi (Interpolated)

64-level

Color Contact  Image Sensor

Laser printer

10

°C—32.5°C, 20—70% RH (Relative Humidity)

×W×D):

Approx. height 255mm x width 420 mm x depth 445 m

Approx. 12kg

Standby: Approx. 6.5 W
Preheat: Approx. 65 W
Copy: Approx. 320 W
Maximum: Approx. 950 W (When the fuser lamp turns on)

220 - 240 V AC, 50 / 60Hz

32 MB

Laser output: Max. 5 mW
Wave length: 760 nm—810 nm
Emission duration: Continuous

18 ppm (page per minute)

600 

× 600 dpi

Model No.

Description

Specifications

KX-FAT92A

Replacement toner cartridge 

1 toner cartridge

KX-FAD93A

Replacement drum unit

1 drum unit

8