Panasonic KX-FM131BX / KX-FM131CX Service Manual ▷ View online
3.4. DOCUMENT READ START POSITION ADJUSTMENT
1. Connect the AC cord.
2. Copy the document and confirm the read start position of the document. Compare the printout (copy) with the original
document.
3. If out of position, adjust the read position.
4. Press the MENU button.
5. Press the #, 9, 0, 0, 0, and 5, 6, 3 buttons.
6. Press the
■
,
■
, SET and MENU buttons.
121
KX-FM131BX / KX-FM131CX
4 DISASSEMBLY INSTRUCTIONS
B
B
B
B
B
B
BOTTOM FRAME
This SCREW COVER prevents the heat
generated by the motor from being con-
ducted through the screw.
generated by the motor from being con-
ducted through the screw.
View (A)
SCREW COVER
SCREW COVER
View (A)
A
A
A
A
Ref. No. 1
HOW TO REMOVE THE BOTTOM FRAME
Procedure
1
1) Remove the 3 screws .
2) Remove the 4 screws .
3) Remove the BOTTOM FRAME.
2) Remove the 4 screws .
3) Remove the BOTTOM FRAME.
122
KX-FM131BX / KX-FM131CX
Ref. No. 2
HOW TO REMOVE THE OPERATION PANEL BLOCK
2) Push the COVER OPEN BUTTON to open
the OPERATION PANEL BLOCK.
3) Tilt the unit vertically so that its left side faces
on a flat surface like a table. While holding
down the grey-shaded ARM as illustrated in
Fig. A , insert a screwdriver and unlatch
the ARM as illustrated in Fig. A .
4) Pull out both sides of the arms (in the direction of
the arrow shown in Fig. B).
5) Remove the OPERATION PANEL BLOCK.
the OPERATION PANEL BLOCK.
3) Tilt the unit vertically so that its left side faces
on a flat surface like a table. While holding
down the grey-shaded ARM as illustrated in
Fig. A , insert a screwdriver and unlatch
the ARM as illustrated in Fig. A .
4) Pull out both sides of the arms (in the direction of
the arrow shown in Fig. B).
5) Remove the OPERATION PANEL BLOCK.
1) Unhook all the connectors connecting
the main cabinet with the OPERATION
PANEL BLOCK.
the main cabinet with the OPERATION
PANEL BLOCK.
Do not let harnesses hang over
the CUTOUT and the OPENING.
the CUTOUT and the OPENING.
Bend two bunches of harnesses
in parallel.
in parallel.
Do not let harnesses overlap
each other.
each other.
Tie harnesses to the ARM with
tape tightly without making a slack.
tape tightly without making a slack.
Be sure not to let harnesses
get caught between the COVER
and the cabinet during the instal-
lation.
get caught between the COVER
and the cabinet during the instal-
lation.
Procedure
1 2
OPERATION PANEL
BLOCK
BLOCK
COVER OPEN
BUTTON
BUTTON
Taping Position
OPERATION PANEL
BLOCK
BLOCK
Fig. B
Fig. B
ARM
OK
OK
NG
View (B)
View (B)
NG
NG
CUTOUT
OPENING
Slack
1
2
Fig. A
OPERATION PANEL BLOCK
123
KX-FM131BX / KX-FM131CX
COVER OPEN BUTTON
View (E)
View (E)
GUIDE
OK
NG
OK
NG
OK
NG
SPRING
OK
CONNECTOR
THERMAL
HEAD
HEAD
Do not leave space between
the PLATE and the THERMAL
HEAD.
the PLATE and the THERMAL
HEAD.
Set the GUIDE in the THERMAL
HEAD correctly.
HEAD correctly.
Make sure that the spring is fitted properly.
Do not let the lead pass
over the rib.
over the rib.
View (D)
View (C)
Thermal Head Ass'y Parts Installation (1)
View (C)
View (D)
GUIDE
ANGLE
B
A
A
A
B
B
Ref. No. 3
HOW TO REMOVE THE THERMAL HEAD
Procedure
3
1) Push the COVER OPEN BUTTON
to open the operation panel.
2) Remove the 2 screws .
3) Remove the ANGLE.
4) Disconnect the CONNECTOR.
5) Remove the thermal head ass'y.
6) Remove the 3 screws .
7) Remove the 2 GUIDEs and the PLATE.
8) Remove the 3 SPRINGs.
9) Remove the THERMAL HEAD.
to open the operation panel.
2) Remove the 2 screws .
3) Remove the ANGLE.
4) Disconnect the CONNECTOR.
5) Remove the thermal head ass'y.
6) Remove the 3 screws .
7) Remove the 2 GUIDEs and the PLATE.
8) Remove the 3 SPRINGs.
9) Remove the THERMAL HEAD.
NG
Rib
Thermal Head Ass'y Parts Installation (2)
PLATE
B
124
KX-FM131BX / KX-FM131CX
Click on the first or last page to see other KX-FM131BX / KX-FM131CX service manuals if exist.