Panasonic KX-FLC418RU Service Manual ▷ View online
89
KX-FLC418RU
10 Test Mode
10.1. Test Functions
The codes listed below can be used to perform simple checks of some of the unit’s functions. When complaints are received
from customers, they provide an effective tool for identifying the locations and causes of malfunctions.
from customers, they provide an effective tool for identifying the locations and causes of malfunctions.
Test Mode
Type of Mode
Code
Function
Operation after code
input
MOTOR TEST &
High Voltage Power
Supply Board
CHECK
High Voltage Power
Supply Board
CHECK
Service Mode
"5" "5" "6"
0: Recording paper feed
1: Auto Document feed (STANDARD)
2: Auto Document feed (FINE)
3: Auto Document feed (SUPER FINE)
Refer to High Voltage Value Check Point (P.132).
1: Auto Document feed (STANDARD)
2: Auto Document feed (FINE)
3: Auto Document feed (SUPER FINE)
Refer to High Voltage Value Check Point (P.132).
SET
MODEM TEST
Service Mode
"5" "5" "4"
Telephone line circuit is connected automatically, output the following signals on
the circuit line.
1) OFF 2) 14400bps 3) 12000bps 4) 96V17
5) 72V17 6) 9600bps 7) 7200bps 8) 4800bps
9) 2400bps 10) 300bps 11) 2100Hz 12) 1100Hz
the circuit line.
1) OFF 2) 14400bps 3) 12000bps 4) 96V17
5) 72V17 6) 9600bps 7) 7200bps 8) 4800bps
9) 2400bps 10) 300bps 11) 2100Hz 12) 1100Hz
SET
ROM CHECK
Service Mode
"5" "5" "1"
Indicates the version and checks the sum of the ROM.
SET
LCD CHECK
Service Mode
"5" "5" "8"
Checks the LCD indication.
Illuminates all the dots to check if they are normal.
Refer to Operation Panel Section (P.125).
Illuminates all the dots to check if they are normal.
Refer to Operation Panel Section (P.125).
SET
LED CHECK
Service Mode
"5" "5" "7"
All LEDs above the operation panel board flash on and off, or are illuminated.
SET
KEY CHECK
Service Mode
"5" "6" "1"
Checks the button operation.
Indicates the button code on the LCD while the button is pressed. Refer to But-
ton Code Table (P.91).
Refer to Operation Panel Section (P.125).
Indicates the button code on the LCD while the button is pressed. Refer to But-
ton Code Table (P.91).
Refer to Operation Panel Section (P.125).
START (any key)
CIS TEST
Service Mode
"5" "5" "5"
LED lights up, CIS scanning.
Refer to CIS (Contact Image Sensor) Section (P.131).
Refer to CIS (Contact Image Sensor) Section (P.131).
LSU TEST
Service Mode
"6" "3" "9"
Laser radiates, Polygon rotates
Refer to LSU Section (P.130).
Refer to LSU Section (P.130).
MEMORY CLEAR
Service Mode
"5" "5" "0"
To reset the value to the default one, except the top margin (#853), left margin
(#854), time / day (#001), logo (#002), Fax no. (#003), History and Directory data.
Please restart a power supply after clearing a memory.
(#854), time / day (#001), logo (#002), Fax no. (#003), History and Directory data.
Please restart a power supply after clearing a memory.
SET
FAN TEST
Service Mode
"6" "7" "7"
1:TEST OFF
2:High-speed rotation
3:Low-speed rotation
2:High-speed rotation
3:Low-speed rotation
SET
MEMORY CLEAR
Service Mode
"7" "1" "0"
Refer to Memory Clear Specification (P.96).
SET
VOICE PROMPT
CHECK
CHECK
Service Mode
"7" "8" "4"
You can hear the voice prompt from speaker after pressing "SET" key.
SET
90
KX-FLC418RU
Note:
The numbers in the boxes (XXX) indicate the keys to be input for the various test modes.
SENSOR CHECK
Service Mode
"8" "1" "5"
First of all, press the copy button, and confirm the action of ON/OFF.
For each sensor's operation, refer to Sensors and Switches Section (P.43).
D S C P R E D T * 3F * D 4 * V : LCD DISPLAY
For each sensor's operation, refer to Sensors and Switches Section (P.43).
D S C P R E D T * 3F * D 4 * V : LCD DISPLAY
D: Document sensor
D: Document set
-: No document
-: No document
S: Paper Feed Sensor
S: Read position
-: No read position
-: No read position
C: Printer Cover Switch
C: Open
-: Close
-: Close
P: Paper sensor
P: Recording paper set
-: No recording paper
-: No recording paper
R: Regist Sensor
R: Detect recording paper
-: Not defect recording paper
-: Not defect recording paper
E: Exit Sensor
E: Detect recording paper
-: Not detect recording paper
-: Not detect recording paper
D: Drum Sensor
D: DRUM set
-: No DRUM
-: No DRUM
T: Toner Sensor
T: Toner sensor ON
-: Toner sensor OFF
-: Toner sensor OFF
*: None
3F: Temperature of THERMISTOR
Hex (00-FF)
*: None
D4: Temperature of Atmosphere
Hex (00-FF)
*: None
V: VOX signal
V: Detect the tone on the line
-: Not detect
-: Not detect
PRINT TEST PAT-
TERN
TERN
Service Mode
"8" "5" "2"
1. Press "852" then the SET key in the service mode.
2. As "PATNO. =" is displayed on the LCD, enter the test pattern No. and press
the SET key.
3. When "No. =" is displayed on the LCD, enter the printing number and press the
SET key. (Press "00" for the infinite printing.)
4. "MODE" is displayed on the LCD. Press "0" to start printing or press "1" to go to
the next screen.
5. When "1" is pressed at MODE, "INTVL =" is displayed on the LCD. Enter the
printing interval (000~999 sec).
6. The printing repeats the designated number of times at the programmed print-
ing intervals.
2. As "PATNO. =" is displayed on the LCD, enter the test pattern No. and press
the SET key.
3. When "No. =" is displayed on the LCD, enter the printing number and press the
SET key. (Press "00" for the infinite printing.)
4. "MODE" is displayed on the LCD. Press "0" to start printing or press "1" to go to
the next screen.
5. When "1" is pressed at MODE, "INTVL =" is displayed on the LCD. Enter the
printing interval (000~999 sec).
6. The printing repeats the designated number of times at the programmed print-
ing intervals.
SET
Test Mode
Type of Mode
Code
Function
Operation after code
input
91
KX-FLC418RU
10.1.1. Button Code Table
92
KX-FLC418RU
10.1.2. Print Test Pattern
1. NO.01
2. NO.06
3. NO.03
• These print test patterns are just image printing, and differ-
ent from actual ones.
When it is required to judge the print quality, compare with
the printing of a nondefective machine.
When it is required to judge the print quality, compare with
the printing of a nondefective machine.
Click on the first or last page to see other KX-FLC418RU service manuals if exist.