Panasonic KX-FLC413UA Service Manual ▷ View online
93
KX-FLC413UA
11.1.3. Service Function Table
Code
Function
Set Value
Effective
Range
Default
Remarks
501
Pause time set
1:3S (Short)
2:5S (Long)
2:5S (Long)
1, 2
1
----------
511
Vox sense
1:HIGH /
2:LOW
2:LOW
1, 2
1
When the TAM (or EXT TAM) does not stop
recording the ICM because noise is detected on
the telephone line, change this setting to "LOW".
recording the ICM because noise is detected on
the telephone line, change this setting to "LOW".
514
Bell signal detect time
X 100msec
1~9
5
----------
520
CED frequency select
1: 2100 Hz
2:1100 Hz
2:1100 Hz
1, 2
1
See Symptom/Countermeasure Table for long dis-
tance and international calls in
tance and international calls in
(
P.104
)
.
521
International mode select
1:ON 2:OFF
1, 2
1
See Symptom/Countermeasure Table for long dis-
tance and international calls in
tance and international calls in
(
P.104
)
.
522
Auto standby select
1:ON 2:OFF
1, 2
1
----------
523
Receive equalizer select
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4
1
Set RX equalizer to automatic mode.
524
Transmission equalizer select
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~4
1
529
Call Service Clear
544
Selecting the document feed position
0~4mm
0~4
2
When the ADF function is incorrect, adjust the
feed position.
feed position.
550
Memory clear
See Test Functions
(
P.88
)
.
551
ROM check
See Test Functions
(
P.88
)
.
553
Monitor on FAX communication select
1:OFF
2:PHASE B
3:ALL
2:PHASE B
3:ALL
1~3
1
Sets whether to monitor the line signal with the
unit's speaker during FAX communication or not.
unit's speaker during FAX communication or not.
554
Modem test
See Test Functions
(
P.88
)
.
555
Scan check
See Test Functions
(
P.88
)
.
556
Motor test
0
See Test Functions
(
P.88
)
.
557
LED test
See Test Functions
(
P.88
)
.
558
LCD test
See Test Functions
(
P.88
)
.
561
KEY test
See Test Functions
(
P.88
)
.
567
T0 timer
X second
001~255
28
Sets a higher value when the response from the
other party needs more time during automatic FAX
transmission.
other party needs more time during automatic FAX
transmission.
570
BREAK % select
1:61% 2:67%
1, 2
1
Sets the % break of pulse dialing according PBX.
571
ITS auto redial time set
X number of
times
times
00~99
03
Selects the number of times that ITS is redialed
(not including the first dial).
(not including the first dial).
572
ITS auto redial line disconnection time
set
set
X second
001~999
065
Sets the interval of ITS redialing.
573
Remote turn-on ring number set
X number of
rings
rings
0~99
20
Sets the number of rings before the unit starts to
receive a document in the TEL mode.
receive a document in the TEL mode.
574
Dial tone detect check
1:ON 2:OFF
1, 2
2
----------
590
FAX auto redial time set
X number of
times
times
00~99
03
Selects the number of redial times during FAX
communication (not including the first dial).
communication (not including the first dial).
591
FAX auto redial time disconnection time
set
set
X second
001~999
065
Sets the FAX redial interval during FAX communi-
cation.
cation.
592
CNG transmit select
1:OFF
2:ALL
3:AUTO
2:ALL
3:AUTO
1~3
2
Lets you select the CNG output during FAX trans-
mission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is per-
formed. OFF: CNG id not output at phase A. Refer
to
mission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is per-
formed. OFF: CNG id not output at phase A. Refer
to
(
P.118
)
.
593
Time between CED and 300bps
1:75 msec
2:500 msec
3:1 sec
2:500 msec
3:1 sec
1~3
1
See Symptom/Countermeasure Table for long
distance and international calls in
distance and international calls in
(
P.104
)
. Refer to
(
P.119
)
and
(
P.104
)
.
594
Overseas DIS detection select
1:detects at the
1st time
2:detects at the
2nd time
1st time
2:detects at the
2nd time
1, 2
1
See Symptom/Countermeasure Table for long
distance and international calls in
distance and international calls in
(
P.104
)
. Refer to
(
P.118
)
and
(
P.104
)
.
595
Receive error limit value set
1: 5%
2: 10%
3: 15%
4: 20%
2: 10%
3: 15%
4: 20%
1~4
2
If the number of errors during transmission
exceeds this value, the sending side terminates
the call.
exceeds this value, the sending side terminates
the call.
94
KX-FLC413UA
596
Transmit level set
X dBm
-15~00
12
Selects the FAX transmission level. Refer to
(
P.118
)
and
(
P.119
)
.
598
Receiving sensitivity
43= -43 dBm
20~48
44
Used when there is an error problem. Refer to
(
P.104
)
.
599
ECM frame size
1:256 2:64
1, 2
1
----------
628
H.V.P.S. check
See Test Functions
(
P.88
)
.
630
Paper Jam Cause Distinction Code
0:No Paper Jam
1:The paper was pulled into the unit.
2:The paper was longer than the maximum length
of the register sensor.
3:The paper exit was not detected after the regis-
tration.
4:The paper was longer than the maximum length
of the paper exit sensor.
5:The register sensor or paper exit sensor was
turned ON before the motor started to rotate.
6:The register sensor chattered.
7:The paper exit sensor chattered.
1:The paper was pulled into the unit.
2:The paper was longer than the maximum length
of the register sensor.
3:The paper exit was not detected after the regis-
tration.
4:The paper was longer than the maximum length
of the paper exit sensor.
5:The register sensor or paper exit sensor was
turned ON before the motor started to rotate.
6:The register sensor chattered.
7:The paper exit sensor chattered.
639
LSU test
See Test Functions
(
P.88
)
.
651
Write system program into the Flash Rom with a tool.
See the parts number of the tool. The tool includes
the operating manual for writing program.
the operating manual for writing program.
655
Cause Distinction Code of Call Service 3
See Call Service Troubleshooting
Guide
Guide
(
P.152
)
.
677
Fan test
See Test Functions
(
P.88
)
.
710
Memory clear except History data
To reset the value to the default one, except His-
tory data. Please restart a power supply after
clearing a memory.
tory data. Please restart a power supply after
clearing a memory.
717
Transmit speed selection
1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~6
1
Adjusts the speed to start training during FAX
transmission. Refer to
transmission. Refer to
(
P.118
).
718
Receive speed selection
1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~6
1
Adjusts the speed to start training during FAX
reception. Refer to
reception. Refer to
(
P.119
)
.
721
Pause tone detect
1:ON 2:OFF
1, 2
2
Selects the tone detection for pause in dialing.
722
Redial tone detect
1:ON 2:OFF
1, 2
1
Sets the tone detection mode after redialing.
731
CPC mode
X10 msec
001~255
033
Sets the CPC signal detection mode from the con-
verter.
verter.
732
Auto disconnect cancel time
1:350 ms
2:1800 ms
3:OFF
2:1800 ms
3:OFF
1~3
1
----------
763
CNG detect time for friendly reception
1:10 sec
2:20 sec
3:30 sec
2:20 sec
3:30 sec
1~3
3
Selects the CNG detection tone of friendly recep-
tion.
tion.
774
T4 timer
X 100 sec
00~99
00
Use this function when delay occurs in the line and
communication.
(ex. Mobile comm) does not work well.
communication.
(ex. Mobile comm) does not work well.
784
Voice prompt test
See Test Functions
(
P.88
)
.
815
Sensor & Vox check
See Test Functions
(
P.88
)
.
852
Print test pattern
See Test Functions
(
P.88
)
.
853
Top margin
1~5
3
----------
854
Left margin
1~7
4
----------
861
Paper size set
1:LETTER
2:A4
3:LEGAL
2:A4
3:LEGAL
1~3
2
----------
874
DTMF ON time
X msec
060~200
100
----------
875
DTMF OFF time
X msec
060~200
100
----------
880
History list
See
(
P.100
)
.
881
Journal 2 list
See
(
P.115
)
.
882
Journal 3 list
See
(
P.115
)
.
961
The time transmitting the false ring
back tone
back tone
X sec
01~10
07
Set the time transmitting the false ring back tone to
the line in TEL/FAX mode.
the line in TEL/FAX mode.
Code
Function
Set Value
Effective
Range
Default
Remarks
95
KX-FLC413UA
11.1.4. Memory Clear Specification
962
The operator calling time
X sec
05~30
10
Set the operator calling time through the speaker
in TEL/Fax mode.
in TEL/Fax mode.
Code
Function
Set Value
Effective
Range
Default
Remarks
96
KX-FLC413UA
11.2. Cordless Handset
Click on the first or last page to see other KX-FLC413UA service manuals if exist.