Panasonic KX-FLC413UA Service Manual ▷ View online
9
KX-FLC413UA
2.3.
Insulation Resistance Test
1. Unplug the power cord and short the two prongs of the plug with a jumper wire.
2. Turn on the power switch.
3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part
2. Turn on the power switch.
3. Measure the resistance value with an ohmmeter between the jumpered AC plug and each exposed metal cabinet part
(screw heads, control shafts, bottom frame, etc.).
Note: Some exposed parts may be isolated from the chassis by design. These will read infinity.
Note: Some exposed parts may be isolated from the chassis by design. These will read infinity.
4. If the measurement is outside the specified limits, there is a possibility of a shock hazard.
2.4.
Battery Caution
Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose used batteries according to the manufacturer’s instructions:
manufacturer. Dispose used batteries according to the manufacturer’s instructions:
The lithium battery is a critical component (type No. BR2032). Please observe for the proper polarity and exact location when
replacing it and the soldering the replacement lithium battery in.
replacing it and the soldering the replacement lithium battery in.
10
KX-FLC413UA
2.5.
Laser Beam and Fuser Unit Section
• The printer of this unit utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
• The fuser unit is inside of the unit and gets hot. Do not touch it when removing the jammed paper or cleaning the lower glass.
11
KX-FLC413UA
3 Specifications
3.1.
Base Unit
* Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the other
party's machine.
** Transmission speed is based upon the ITU-T No. 1 Test Chart. (Refer to ITU-T No.1 Test Chart (P.261).) If the capability of the
other party's machine is inferior to your unit, the transmission time may be longer.
*** If an error occurs during fax reception, such as a paper jam or if the recording paper runs out, the fax and subsequent faxes will
be retained in memory.
**** Recording time may be reduced by the calling party's back-
party's machine.
** Transmission speed is based upon the ITU-T No. 1 Test Chart. (Refer to ITU-T No.1 Test Chart (P.261).) If the capability of the
other party's machine is inferior to your unit, the transmission time may be longer.
*** If an error occurs during fax reception, such as a paper jam or if the recording paper runs out, the fax and subsequent faxes will
be retained in memory.
**** Recording time may be reduced by the calling party's back-
ground noise.
Note:
• Design and specifications are subject to change without notice.
• The pictures and illustrations in these instructions may vary slightly from the actual product.
Applicable Lines:
Public Switched Telephone Network
Document Size:
Max. 216 mm in width
Max. 600 mm in length
Max. 600 mm in length
Effective Scanning Width:
208 mm
Effective Printing Width:
202mm
Transmission Time*:
Approx. 8 s/page (ECM-MMR)**
Scanning Density:
Horizontal:
8 pels/mm
Vertical:
3.85 lines/mm -STANDARD
7.7 lines/mm -FINE/PHOTO/MIXED(PHOTO WITH TEXT)
15.4 lines/mm -SUPER FINE
8 pels/mm
Vertical:
3.85 lines/mm -STANDARD
7.7 lines/mm -FINE/PHOTO/MIXED(PHOTO WITH TEXT)
15.4 lines/mm -SUPER FINE
Photo Resolution:
64-level
Scanner Type:
Contact Image Sensor (CIS)
Printer Type:
Laser printer
Data Compression System:
Modified Huffman (MH), Modified READ (MR), Modified, Modified READ (MMR)
Modem Speed:
14,400/12,000/9,600/7,200/4,800/2,400 bps; Automatic Fallback
Operating Environment:
10
°C—32.5°C, 20—70% RH (Relative Humidity)
Dimensions (H
×W×D):
218 mm
× 360 mm × 357 mm
Mass (Weight):
Approx. 7.5 kg
Power Consumption:
Standby: Approx. 4 W
Transmission: Approx. 12W
Reception: Approx. 240 W
Copy: Approx. 240 W
Maximum: Approx. 950W (When the fuser lamp turns on)
Transmission: Approx. 12W
Reception: Approx. 240 W
Copy: Approx. 240 W
Maximum: Approx. 950W (When the fuser lamp turns on)
Power Supply:
220-240 V AC, 50/60Hz
FAX Memory Capacity***:
Approx. 150 pages of memory transmission.
Approx. 40 pages of memory reception.
(Based on ITU-T No. 1 Test Chart in standard resolution.)
Approx. 40 pages of memory reception.
(Based on ITU-T No. 1 Test Chart in standard resolution.)
Voice memory capacity****:
Approx. 15 minutes of recording time
Copy memory capacity:
Approx. 80 pages (Based on the ITU-T No. 1 Test Chart in fine resolution.)
Laser diode properties:
Laser output: Max. 5 mW
Wave length: 760 nm—800 nm
Emission duration: Continuous
Wave length: 760 nm—800 nm
Emission duration: Continuous
LED light of CIS properties:
LED radiation output: Max. 1 mW
Wavelength: Green 520 nm typ.
Emission duration: Continuous
Wavelength: Green 520 nm typ.
Emission duration: Continuous
Print Speed:
10 ppm (page per minute)
Printing Resolution:
600
× 600 dpi
12
KX-FLC413UA
3.2.
Cordless Handset
3.3.
Charger Unit
4 General/Introduction
4.1.
Optional Accessories
Standard:
DECT (Digital Enhanced Cordless Telecommunications)
GAP (Generic Access Profile)
GAP (Generic Access Profile)
Number of channels:
120 Duplex Channels
Frequency range:
1.88 GHz to 1.9 GHz
Duplex procedure:
TDMA (Time Division Multiple Access)
Channel spacing:
1,728 kHz
Bit rate:
1,152 kbit/s
Modulation:
GFSK (Gaussian Frequency Shift Keying)
RF transmission power:
Approx. 250 mW
Voice coding:
ADPCM 32 kbit/s
Operating environment:
5
°C - 40 °C, 20 % - 80 % RH (Relative Humidity)
Dimensions:
Approx. height 155 mm
× width 48 mm × depth 34 mm
Mass (Weight):
Approx. 140 g
Operating environment:
5
°C - 40 °C, 20 % - 80 % RH (Relative Humidity)
Dimensions:
Approx. height 61 mm
× width 87 mm × depth 95 mm
Mass (Weight):
Approx. 90 g
Power consumption:
Standby: Approx. 1.5 W
Maximum: Approx. 3 W
Maximum: Approx. 3 W
Power supply:
AC adaptor (220 V - 240 V AC, 50/60 Hz)
Model No.
Description
Specifications
KX-FAT88A
Toner cartridge
1 toner cartridge
KX-FAD89A
Drum unit
1 drum unit
P03P
Rechargeable nickel metal hydride (Ni-MH) battery 2 batteries (AAA (R03) size)
KX-A272
DECT repeater
-
Click on the first or last page to see other KX-FLC413UA service manuals if exist.