Panasonic KX-FL403UA Service Manual ▷ View online
Refer to JOURNAL 3 in PRINTOUT EXAMPLE(P.121).
(6) ENCODE
Compression Code: MH/MR/MMR
(7) MSLT
MSLT means Minimum Scan Line Time. Used only at
the factory.
the factory.
(8) EQM
EQM means Eye Quality Monitor. Used only at the
factory.
factory.
(9) ERROR LINE (RX)
When an error occurs while receiving a fax, this shows
the number of error lines.
the number of error lines.
(10) MAKER CODE
This shows a 2 digit code of the other party´s fax
machine brand.
machine brand.
0E: “KX” model
00: Unknown
79: “UF” model
19: “Xerox” model
6.5.11.2. JOURNAL 3
Description
6.5.11.3. PRINTOUT EXAMPLE
121
KX-FL403UA
122
KX-FL403UA
Error code table: Refer to ERROR MESSAGE (P.4).
6.5.11.4. HOW TO OUTPUT THE JOURNAL REPORT
1. Press the MENU button.
2. Press “#”, then “8” and “3”.
3. Press the SET button.
4. The report prints out.
CROSS REFERENCE:
FEATURES(P.11)
(1) CODE
(2) RESULT
(3) MODE
SYMPTOM
Counter-
measure*
PRESSED THE STOP KEY
SND & RCV Communication was interrupted by the STOP button.
DOCUMENT JAMMED
SND
The document paper is jammed.
NO DOCUMENT
SND
No document paper.
THE COVER WAS OPENED
SND
The cover is open.
28
COMMUNICATION ERROR
SND & RCV
---------
40
COMMUNICATION ERROR
SND
Transmission is finished when the T1 TIMER expires.
1
41
COMMUNICATION ERROR
SND
DCN is received after DCS transmission.
2
42
COMMUNICATION ERROR
SND
FTT is received after transmission of a 2400BSP training signal.
3
43
COMMUNICATION ERROR
SND
No response after post message is transmitted three times.
4
44
COMMUNICATION ERROR
SND
RTN and PIN are received.
5
46
COMMUNICATION ERROR
RCV
No response after FTT is transmitted.
6
48
COMMUNICATION ERROR
RCV
No post message.
7
49
COMMUNICATION ERROR
RCV
RTN is transmitted.
8
50
COMMUNICATION ERROR
RCV
PIN is transmitted (to PRI-Q).
8
51
COMMUNICATION ERROR
RCV
PIN is transmitted.
8
52
COMMUNICATION ERROR
RCV
Reception is finished when the T1 TIMER expires.
9
54
ERROR-NOT YOUR UNIT
RCV
DCN is received after DIS transmission.
11
58
COMMUNICATION ERROR
RCV
DCN is received after FTT transmission.
13
59
ERROR-NOT YOUR UNIT
SND
DCN responds to the post message.
14
65
COMMUNICATION ERROR
SND
DCN is received before DIS reception.
2
65
COMMUNICATION ERROR
RCV
Reception is not EOP, EOM PIP, PIN, RTP or RTN.
2
68
COMMUNICATION ERROR
RCV
No response at the other party after MCF or CFR is transmitted.
13
70
ERROR-NOT YOUR UNIT
RCV
DCN is received after CFR transmission.
13
72
COMMUNICATION ERROR
RCV
Carrier is cut when the image signal is received.
16
75
MEMORY FULL
RCV
The document was not received due to memory full.
79
CANCELED
SND
The multi-station transmission was rejected by the user.
FF
COMMUNICATION ERROR
SND & RCV Modem error. For the DCN, DCN, etc. abbreviations, refer to
MODEM SECTION (P.215).
12
SND=TRANSMISSION / RCV=RECEPTION
Most fax communication problems can be resolved by the following steps.
1. Change the transmit level. (Service code: 596, refer to SERVICE FUNCTION TABLE(P.65).)
2. Change the TX speed/RX speed. (Service code: 717/718, refer to SERVICE FUNCTION TABLE (P.65).)
123
KX-FL403UA
Note*:
If the problem remains, see the following “Countermeasure” flow chart.
124
KX-FL403UA
Click on the first or last page to see other KX-FL403UA service manuals if exist.