Panasonic H-FS14140PP / H-FS14140E / H-FS14140GK Service Manual ▷ View online
17
4.3.7.
Installation of the Ring mount base
1. Tighten 2 screws (G) in numerical order by using the
torque driver with specified torque.
(Torque Driver : RFKZ0456)
(Torque : 10 ± 1 N ･ cm)
(Torque Driver : RFKZ0456)
(Torque : 10 ± 1 N ･ cm)
2. Tighten 3 screws (F) in numerical order by using the
torque driver with specified torque.
(Torque Driver : RFKZ0456)
(Torque : 10 ± 1 N ･ cm)
(Torque Driver : RFKZ0456)
(Torque : 10 ± 1 N ･ cm)
18
4.3.8.
Installation of the Lens P.C.B.unit
and the Lens mount contact unit
and the Lens mount contact unit
1. Connect 4 connectors.
4.3.9.
Installationl of the Rear frame unit
1. Connect 1 connector and tighten 3 screws (E) in numeri-
cal order by using the torque driver with specified torque.
(Torque Driver : RFKZ0456)
(Torque : 8 ± 1 N ･ cm)
(Torque Driver : RFKZ0456)
(Torque : 8 ± 1 N ･ cm)
4.3.10. Installation of the L mount unit
1. Tighten 1 screw (C) and 3 screws (D) in numerical order
by using the torque driver with specified torque.
(Torque Driver : RFKZ0456)
(Torque for screw (D) : 20±1.2N ･ cm,
Torque for screw (C) : 8±1N ･ cm)
(Torque Driver : RFKZ0456)
(Torque for screw (D) : 20±1.2N ･ cm,
Torque for screw (C) : 8±1N ･ cm)
19
4.3.11. Installation of the Shading frame
1. Tighten 2 screws (B) in numerical order by using the
torque driver with specified torque.
(Torque Driver : RFKZ0456)
(Torque for screw (B) : 10±1N ･ cm)
(Torque Driver : RFKZ0456)
(Torque for screw (B) : 10±1N ･ cm)
20
5 Maintenance
5.1.
Lens Cleaning
5.1.1.
Dust / Dirt on the outer casing part(s)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
5.1.2.
Dust / Dirt on the Lens Glasses
Define the location of the dust / dirt first, whether it is outside lens surface or not.
1. When it is outside surface of the lens
When the dust and / or dirt gets on the outer side surface of the Lens glasses, order the following procedures.
a. Blow off the dust on the Lens glass surface with the Blower, gently. (Do not Blow too strongly.)
b. Wipe out the dirt on the lens glass surface with Lens cleaning KIT (VFK1900BK) if necessary.
b. Wipe out the dirt on the lens glass surface with Lens cleaning KIT (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in the Lens cleaning KIT in details.)
2. When it is inside of the lens
When there is dust / dirt inside surface of the 1st lens holder, Cam barrel, remove it by referring to the following procedures.
1. When removing 1st lens holder,Cam barrel, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "3.2. Clean Box", in details.
As for clean box, refer to the "3.2. Clean Box", in details.
2. When install the screws, use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, can only use the original 1st lens holder,Cam barrel .
3. To keep the Lens performance, can only use the original 1st lens holder,Cam barrel .
So the 1st lens holder,Cam barrel are not supplied as spare parts.
Also do not exchange the 1st lens holder,Cam barrel taking from others.
Also do not exchange the 1st lens holder,Cam barrel taking from others.