Panasonic DMC-ZX1EB / DMC-ZX1EE / DMC-ZX1EF / DMC-ZX1EG / DMC-ZX1EP / DMC-ZX1SG / DMC-ZR1P / DMC-ZR1PC / DMC-ZR1PR / DMC-ZR1PU / DMC-ZR1GC / DMC-ZR1GD / DMC-ZR1GH / DMC-ZR1GK / DMC-ZR1GN / DMC-ZR1GT Service Manual ▷ View online
37
8.5.8.
Phase alignment of the 1st Direct
Frame Unit/1st Lens Frame Unit/
2nd Lens Frame Unit/Both Sides
Cam Frame/2nd 3rd Direct Frame/
3rd Lens Frame Unit and Fixed
Frame Unit/Drive Frame Unit/Pene-
tration Cam Frame
Frame Unit/1st Lens Frame Unit/
2nd Lens Frame Unit/Both Sides
Cam Frame/2nd 3rd Direct Frame/
3rd Lens Frame Unit and Fixed
Frame Unit/Drive Frame Unit/Pene-
tration Cam Frame
8.5.9.
Install of the Master Flange Unit
38
8.5.10.
Install of the Lens FPC Unit and
Zoom Motor
Zoom Motor
8.6.
Removal of the CCD Unit
To prevent the CCD unit from catching the dust and dirt, do not
remove the CCD unit except for replacing.
remove the CCD unit except for replacing.
39
8.7.
Removal
of
the
Focus
Motor
8.8.
The Application of Grease
Method
Method
The grease application parts of lens unit are as follows.
Apply grease additionally in the specified position if necessary.
When the grease is applied, use a toothpick and apply thinly.
Apply grease additionally in the specified position if necessary.
When the grease is applied, use a toothpick and apply thinly.
• Focus motor (lead screw)/Fasten groove of nut/Guide pole
- Grease: RFKZ0472
- Amount of application: 2 - 4 mg
- Amount of application: 2 - 4 mg
• Positioning pole
- Grease: RFKZ0472
- Amount of application: 1 - 2 mg
- Amount of application: 1 - 2 mg
40
9 Measurements and Adjustments
9.1.
Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-AVC”.
NOTE:
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-AVC”.
NOTE:
After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.
*1: This adjustment is necessary, not only replacing CCD unit but also removing it from the lens unit.
NOTE:
*There is no LCD adjustment in this model.
Replaced Part
Adjustment Item
Main
P.C.B.
Rear
OPE FPC
Unit
Flash Top
P.C.B.
VENUS
(IC6001)
Flash-
ROM
(IC6002)
Lens Part
(Excluding
CCD)
CCD Unit
GYRO
(IC7301/
IC9501)
Camera
Section
Section
OIS hall element adjustment
(OIS)
(OIS)
O
-
-
O
O
O
-
-
Back focus adjustment,
Gyro adjustment
(BF)
Gyro adjustment
(BF)
O
O
O
O
O
O
O
*1
O
Shutter adjustment
(SHT)
(SHT)
O
-
-
O
O
O
O
-
ISO sensitivity adjustment
(ISO)
(ISO)
O
-
-
O
O
O
O
-
AWB adjustment,
High brightness coloration inspection
(WBL)
High brightness coloration inspection
(WBL)
O
-
-
O
O
O
O
-
CCD white scratch compensation
(WKI)
(WKI)
O
-
-
O
O
-
O
*1
-
CCD black scratch compensation
(BKI)
(BKI)
O
-
-
O
O
-
O
*1
-
Venus zoom inspection
(PZM)
(PZM)
O
-
-
O
O
-
-
-
Monitor linearity inspection
(MLN)
(MLN)
O
-
-
O
O
O
O
-
Colour reproduction inspection,
MIC inspection
(COL)
MIC inspection
(COL)
O
-
-
O
O
O
O
-
Click on the first or last page to see other DMC-ZX1EB / DMC-ZX1EE / DMC-ZX1EF / DMC-ZX1EG / DMC-ZX1EP / DMC-ZX1SG / DMC-ZR1P / DMC-ZR1PC / DMC-ZR1PR / DMC-ZR1PU / DMC-ZR1GC / DMC-ZR1GD / DMC-ZR1GH / DMC-ZR1GK / DMC-ZR1GN / DMC-ZR1GT service manuals if exist.