Panasonic DMC-ZX1EB / DMC-ZX1EE / DMC-ZX1EF / DMC-ZX1EG / DMC-ZX1EP / DMC-ZX1SG / DMC-ZR1P / DMC-ZR1PC / DMC-ZR1PR / DMC-ZR1PU / DMC-ZR1GC / DMC-ZR1GD / DMC-ZR1GH / DMC-ZR1GK / DMC-ZR1GN / DMC-ZR1GT Service Manual ▷ View online
29
8.3.11.
Removal of the Battery Case Unit
(Fig.D14)
8.3.12.
Removal of the Jack Door
(Fig.D15)
8.3.13.
Removal of the Battery Door Unit
(Fig.D16)
NOTE: (When Installing)
Be sure to confirm the following points when installing.
• The Screw is tightened enough.
• Installing conditions are fine. (No distortion, no illegal-
• Installing conditions are fine. (No distortion, no illegal-
space.)
• No dust and/or dirt on every Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
30
8.4.
Disassembly Procedure for the
Lens
Lens
NOTE: When Disassembling and Assembling for the Lens
1. To minimize the possibility of the CCD being dirt, perform
disassemble and/or assemble under the condition of the
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6..
CCD is being mounted.
Disassembling procedures for the CCD unit, refer to item
8.6..
2. Take care that the dust and dirt are not entered into the
lens.
In case of the dust is putted on the lens, blow off them by
airbrush.
In case of the dust is putted on the lens, blow off them by
airbrush.
3. Do not touch the surface of lens.
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (RFKZ0472) to the point where is
4. Use lens cleaning KIT (BK)(VFK1900BK).
5. Apply the grease (RFKZ0472) to the point where is
shown to “THE APPLICATION OF GREASE METHOD“ in
the figure.
When the grease is applied, use a toothpick and apply
thinly.
the figure.
When the grease is applied, use a toothpick and apply
thinly.
6. When repair the fixed frame unit, drive frame unit and
penetration cam frame, must be unit exchange.
8.4.1.
Removal of the Zoom Motor and
Lens FPC Unit
Lens FPC Unit
1. Remove the 7 solders (A).
2. Remove the 1 lock.
3. Unscrew the 2 screws (A).
4. Remove the zoom motor to the direction of arrow (1).
5. Remove the 4 solders (B).
2. Remove the 1 lock.
3. Unscrew the 2 screws (A).
4. Remove the zoom motor to the direction of arrow (1).
5. Remove the 4 solders (B).
31
6. Unscrew the 1 screw (B).
7. Remove the photo sensor.
8. Remove the 16 solders (C).
9. Remove the 5 locks.
7. Remove the photo sensor.
8. Remove the 16 solders (C).
9. Remove the 5 locks.
10. Remove the lens FPC unit to the direction of arrow (2).
8.4.2.
Removal of the Master Flange Unit
1. Unscrew the 4 screws (C).
2. Remove the master flange unit.
32
8.4.3.
Removal of the 1st Lens Frame
Unit/2nd Lens Frame Unit/Both
Sides Cam Frame/2nd 3rd Direct
Frame/3rd Lens Frame Unit
Unit/2nd Lens Frame Unit/Both
Sides Cam Frame/2nd 3rd Direct
Frame/3rd Lens Frame Unit
1. Push the both sides cam frame from the lens front side in
the direction of arrow, and then remove the unit of 1st
lens frame unit/2nd lens frame unit/both sides cam frame/
2nd 3rd direct frame/3rd lens frame unit from the fixed
frame unit/drive frame unit/penetration cam frame/1st
direct frame unit.
lens frame unit/2nd lens frame unit/both sides cam frame/
2nd 3rd direct frame/3rd lens frame unit from the fixed
frame unit/drive frame unit/penetration cam frame/1st
direct frame unit.
8.4.4.
Removal of the 2nd Lens Frame
Unit/Both Sides Cam Frame/2nd
3rd Direct Frame/3rd Lens Frame
Unit
Unit/Both Sides Cam Frame/2nd
3rd Direct Frame/3rd Lens Frame
Unit
1. Turn the 2nd lens frame unit/both sides cam frame/2nd
3rd direct frame/3rd lens frame unit in the direction of the
arrow (1) fully, and then remove them in the direction of
the arrow (2).
arrow (1) fully, and then remove them in the direction of
the arrow (2).
Click on the first or last page to see other DMC-ZX1EB / DMC-ZX1EE / DMC-ZX1EF / DMC-ZX1EG / DMC-ZX1EP / DMC-ZX1SG / DMC-ZR1P / DMC-ZR1PC / DMC-ZR1PR / DMC-ZR1PU / DMC-ZR1GC / DMC-ZR1GD / DMC-ZR1GH / DMC-ZR1GK / DMC-ZR1GN / DMC-ZR1GT service manuals if exist.