Panasonic DMC-TZ5P / DMC-TZ5PC / DMC-TZ5PL / DMC-TZ5PR / DMC-TZ5EB / DMC-TZ5EE / DMC-TZ5EF / DMC-TZ5EG / DMC-TZ5E / DMC-TZ5SG / DMC-TZ15GC / DMC-TZ15GD / DMC-TZ15GK / DMC-TZ15GN / DMC-TZ15GT / DMC-TZ15GJ Service Manual ▷ View online
9
3 Service Navigation
3.1.
Introduction
This service manual contains technical information, which will allow service personnel's to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2.
General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30
°C (86 °F) more than that of the
normal solder.
Definition of PCB Lead Free Solder being used
Definition of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
• (Definition: The letter of
is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees
C (662±86
°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
3.3.
Important Notice 1:(Other than U.S.A. and Canadian Market)
1. The service manual does not contain the following information, because of the impossibility of servicing at component level
without concerned equipment/facilities.
a. Schematic diagram, Block Diagram and PCB layout of MAIN PCB and SUB PCB.
b. Parts list for individual parts for MAIN PCB and SUB PCB.
b. Parts list for individual parts for MAIN PCB and SUB PCB.
When a part replacement is required for repairing MAIN PCB and/or SUB PCB, replace as an assembled parts. (MAIN PCB/
SUB PCB)
SUB PCB)
2. The following category is/are recycle module part. please send it/them to Central Repair Center.
• MAIN PCB (VEP56063A)
• SUB PCB (VEP51020A)
• SUB PCB (VEP51020A)
The letter of
is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)
10
3.4.
How to Define the Model Suffix (NTSC or PAL model)
There are eight kinds of DMC-TZ5/TZ15, regardless of the colours.
• a) DMC-TZ5 (Japan domestic model.)
• b) DMC-TZ5P/PC
• c) DMC-TZ5EB/EF/EG/E
• d) DMC-TZ5EE
• e) DMC-TZ15GD
• f) DMC-TZ15GT
• g) DMC-TZ15GN
• h) DMC-TZ5PL/PR/SG, TZ15GC/GK/GJ
• b) DMC-TZ5P/PC
• c) DMC-TZ5EB/EF/EG/E
• d) DMC-TZ5EE
• e) DMC-TZ15GD
• f) DMC-TZ15GT
• g) DMC-TZ15GN
• h) DMC-TZ5PL/PR/SG, TZ15GC/GK/GJ
(DMC-TZ5S is exclusively Japan domestic model.)
What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash ROM mounted on Main PCB.
What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash ROM mounted on Main PCB.
3.4.1.
Defining methods
To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE:
After replacing the MAIN PCB, be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site
in “TSN system”, together with Maintenance software.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site
in “TSN system”, together with Maintenance software.
11
3.4.2.
INITIAL SETTINGS:
When you replace the Main PCB, be sure to perform the initial settings after achieving the adjustment by ordering the following pro-
cedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
cedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, be sure to read the following CAUTIONS.
2. PROCEDURES:
• Preparation. Proceed the picture back up from the unit (Refer to above "CAUTION 2")
• Step 1. The temporary cancellation of initial setting:
• Step 1. The temporary cancellation of initial setting:
Set the REC/PLAY switch to “[ Recording ]”.
Set the mode dial to “[ Normal picture mode ] (Red camera mark)”.
While keep pressing [ E. zoom switch ] and “[ UP ] of Cross Key” simultaneously, turn the Power on.
Set the mode dial to “[ Normal picture mode ] (Red camera mark)”.
While keep pressing [ E. zoom switch ] and “[ UP ] of Cross Key” simultaneously, turn the Power on.
• Step 2. The cancellation of initial setting:
Set the REC/PLAY switch to “[ Playback ]”.
Press [ E. zoom switch ] and “[ UP ] of Cross Key” simultaneously, then turn the Power off.
Press [ E. zoom switch ] and “[ UP ] of Cross Key” simultaneously, then turn the Power off.
• Step 3. Turn the Power on:
Set the REC/PLAY switch to “[ Recording ]”.
Set the mode dial to “[ Normal picture mode ] (Red camera mark)”, and then turn the Power on.
Set the mode dial to “[ Normal picture mode ] (Red camera mark)”, and then turn the Power on.
• Step 4. Display the INITIAL SETTING:
While keep pressing [ MENU ] and “[ RIGHT ] of Cross Key” simultaneously, turn the Power off.
12
• Step 5. Set the INITIAL SETTING: (Refer to “CAUTION 1”)
[Caution for before settings]
Once "NONE(JAPAN)" (Area for Japan) or "P" (Area for North America) is selected with "INITIAL SETTINGS", other areas
will not displayed even if "INITIAL SETTINGS" menu is displayed again, thus, the area can not be changed.
Select the area carefully.
will not displayed even if "INITIAL SETTINGS" menu is displayed again, thus, the area can not be changed.
Select the area carefully.
Select the area with pressing “[ UP ]/[ DOWN ] of Cross Key”, and then press the “[ RIGHT ] of Cross Key”.
The only set area is displayed, and then press the “[ RIGHT ] of Cross key” after confirmation.
(The unit is powered off automatically.)
Confirm the display of “PLEASE SET THE CLOCK” in English when the unit is turned on again.
(The unit is powered off automatically.)
Confirm the display of “PLEASE SET THE CLOCK” in English when the unit is turned on again.
• Step 6. CONFIRMATION:
The display shows “PLEASE SET THE CLOCK” when turn the Power on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
(When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)
When the unit is connected to PC with USB cable, it is detected as removable media.
(When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)
1) As for your reference Default setting condition is given in the following table.
• Default setting (After “INITIAL SETTINGS”)
MODEL
VIDEO OUTPUT
LANGUAGE
DATE
REMARKS
a)
DMC-TZ5S
NTSC
Japanese
Year/Month/Date
b)
DMC-TZ5P/PC/PL
NTSC
English
Month/Date/Year
c)
DMC-TZ5EB/EG/E/SG/PR
DMC-TZ15GC/GN/GJ
DMC-TZ15GC/GN/GJ
PAL
English
Date/Month/Year
d)
DMC-TZ5EF
PAL
French
Date/Month/Year
e)
DMC-TZ5EE
PAL
Russian
Date/Month/Year
f)
DMC-TZ15GK
PAL
Chinese (simplified)
Year/Month/Date
g)
DMC-TZ15GT
NTSC
Chinese (traditional)
Year/Month/Date
h)
DMC-TZ15GD
NTSC
Korean
Year/Month/Date
Click on the first or last page to see other DMC-TZ5P / DMC-TZ5PC / DMC-TZ5PL / DMC-TZ5PR / DMC-TZ5EB / DMC-TZ5EE / DMC-TZ5EF / DMC-TZ5EG / DMC-TZ5E / DMC-TZ5SG / DMC-TZ15GC / DMC-TZ15GD / DMC-TZ15GK / DMC-TZ15GN / DMC-TZ15GT / DMC-TZ15GJ service manuals if exist.