Panasonic DMC-LX3P / DMC-LX3PC / DMC-LX3PL / DMC-LX3E / DMC-LX3EB / DMC-LX3EE / DMC-LX3EF / DMC-LX3EG / DMC-LX3GC / DMC-LX3GD / DMC-LX3GK / DMC-LX3GN / DMC-LX3GT / DMC-LX3GJ / DMC-LX3SG Service Manual ▷ View online
17
The above table
1) About "*" indication:
The third digit from the left is different as follows.
1) About "*" indication:
The third digit from the left is different as follows.
- In case of 0 (example: 18
001000)
When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been
completed.
It means that this error is occurred basically at user side.
completed.
It means that this error is occurred basically at user side.
- In case of 8 (example: 18
801000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been
released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
•
6. How to returned to Normal Display:
Turn the power off and on, to exit from Error code display mode.
Turn the power off and on, to exit from Error code display mode.
NOTE:
The error code can not be initialized.
HARD
VENUS A/D
Flash
28*0
0000
Flash charging error.
IC6001-(AC17) signal line or Flash charging circuit
IC6001-(AC17) signal line or Flash charging circuit
FLASH ROM
(EEPROM
Area)
(EEPROM
Area)
FLASH ROM
(EEPROM
Area)
2B*0
0001
EEPROM read error
IC6002 (FLASH ROM)
IC6002 (FLASH ROM)
0002
EEPROM write error
IC6002 (FLASH ROM)
IC6002 (FLASH ROM)
0008
SDRAM error
SDRAM Mounting defective
SDRAM Mounting defective
SYSTEM
RTC
2C*0
0001
SYSTEM IC initialize failure error
Communication between IC6001 (VENUS 4) and IC9101 (SYSTEM)
Communication between IC6001 (VENUS 4) and IC9101 (SYSTEM)
SOFT
CPU
Reset
30*0
0001
|
0007
NMI reset
Non Mask-able Interrupt
(30000001-30000007 are caused by factors)
Non Mask-able Interrupt
(30000001-30000007 are caused by factors)
Card
Card
31*0
0001
Card logic error
SD memory card data line or IC6001 (VENUS 4)
SD memory card data line or IC6001 (VENUS 4)
0002
Card physical error
SD memory card data line or IC6001 (VENUS 4)
SD memory card data line or IC6001 (VENUS 4)
0004
Write error
SD memory card data line or IC6001 (VENUS 4)
SD memory card data line or IC6001 (VENUS 4)
39*0
0005
Format error
CPU,
ASIC hard
ASIC hard
Stop
38*0
0001
Camera task finish process time out.
Communication between Lens system and IC6001 (VENUS 4)
Communication between Lens system and IC6001 (VENUS 4)
0002
Camera task invalid code error.
IC6001 (VENUS 4)
IC6001 (VENUS 4)
0100
File time out error in recording motion image
IC6001 (VENUS 4)
IC6001 (VENUS 4)
0200
File data cue send error in recording motion image
IC6001 (VENUS 4)
IC6001 (VENUS 4)
0300
Single or burst recording brake time out.
Memory area
3A*0
0008
USB work area partitioning failure
USB dynamic memory securing failure when connecting
USB dynamic memory securing failure when connecting
Operation
Power on
3B*0
0000
FLASHROM processing early period of camera during movement.
Zoom
Zoom
3C*0
0000
Inperfect zoom lens processing
Zoom lens
Zoom lens
35*0
0000
|
FFFF
Software error
(0-7bit : command, 8-15bit : status)
(0-7bit : command, 8-15bit : status)
35*1
0000
Though record preprocessing is necessary, it is not called.
35*2
0000
Though record preprocessing is necessary, it is not completed.
Attribute
Main item
Sub item
Error code
Contents (Upper)
High 4 bits Low 4 bits
Check point (Lower)
18
7 Service Fixture & Tools
7.1.
Service Fixture and Tools
The following Service Fixture and tools are used for checking and servicing this unit.
19
7.2.
When Replacing the Main PCB
After replacing the MAIN PCB, be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in
“TSN system”, together with Maintenance software.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in
“TSN system”, together with Maintenance software.
7.3.
Service Position
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No.
Parts No.
Connection
Form
1
VFK1951
FP9001 (MAIN) - CCD UNIT
39PIN 0.3 FFC
2
RFKZ0477
FP9003 (MAIN) - LCD UNIT
45PIN 0.3 FFC
3
RFKZ1974
FP9004 (MAIN) - LCD UNIT
4PIN 0.5 FFC
4
RFKZ0477
FP9005 (MAIN) - LENS UNIT
45PIN 0.3 FFC
5
VFK1480
FP9006 (MAIN) - AF/MF ASPECT FPC UNIT
6PIN 0.5 FFC
6
VFK1870
PP9001 (MAIN) - PS9901 (TOP)
30PIN B to B
20
CAUTION-1. (When servicing FLASH PCB)
1. Be sure to discharge the capacitor on FLASH PCB.
Refer to “HOW TO DISCHARGE THE CAPACITOR ON FLASH PCB”.
The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on FLASH PCB.
3. DO NOT allow other parts to touch the high voltage circuit on FLASH PCB.
3. DO NOT allow other parts to touch the high voltage circuit on FLASH PCB.
Click on the first or last page to see other DMC-LX3P / DMC-LX3PC / DMC-LX3PL / DMC-LX3E / DMC-LX3EB / DMC-LX3EE / DMC-LX3EF / DMC-LX3EG / DMC-LX3GC / DMC-LX3GD / DMC-LX3GK / DMC-LX3GN / DMC-LX3GT / DMC-LX3GJ / DMC-LX3SG service manuals if exist.