Panasonic DMC-LC1PP / DMC-LC1EB / DMC-LC1EG / DMC-LC1GC / DMC-LC1GD / DMC-LC1GN (serv.man2) Service Manual ▷ View online
6 HOW TO REPLACE THE LITHIUM BATTERY
6.1. REPLACEMENT PROCEDURE
1. Remove the MAIN C.B.A. (Refer to Disassembly Procedures.)
2. Remove the Lithium battery (Ref. No. “Z9101” at component side of MAIN C.B.A.) and then replace it into new one.
NOTE:
This Lithium battery is a critical component. (Type No.: ML614S Manufactured by Matsushita Battery Industrial Co.,Ltd.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
9
DMC-LC1PP / DMC-LC1EB / DMC-LC1EG / DMC-LC1GC / DMC-LC1GD / DMC-LC1GN
10
DMC-LC1PP / DMC-LC1EB / DMC-LC1EG / DMC-LC1GC / DMC-LC1GD / DMC-LC1GN
7 SERVICE NOTES
7.1. WHEN REPLACING THE MAIN C.B.A.
After replacing the MAIN C.B.A., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “CS-Web from AVC” web-site in “TSN system”, together with
Maintenance software.
Maintenance software.
7.2. SERVICE POSITION
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No.
Parts No.
Connection
Form
1
VFK1388
FP9006 (MAIN) - REAR OPERATION UNIT
12PIN 0.5 FFC
2
VFK1284
FP9007 (MAIN) - LENS UNIT
24PIN 0.5 FFC
3
VFK1440
FP9008 (MAIN) - AF SENSOR
10PIN 0.5 FFC
4
VFK1284
FP9009 (MAIN) - LCD UNIT
24PIN 0.5 FFC
5
VFK1576DC04
P9002 (MAIN) - LCD BACKLIGHT
2PIN CABLE
6
VFK1576DC202
P9004 (MAIN) - SPEAKER
2PIN CABLE
7
VFK1712
FP9003 (MAIN) - FP8502 (JACK-FLASH)
20PIN 0.5 FFC
CAUTION-1. (When servicing JACK-FLASH C.B.A.)
1. Be sure to discharge the capacitor on JACK-FLASH C.B.A.
Refer to “HOW TO DISCHARGE THE CAPACITOR ON JACK-FLASH C.B.A.”.
The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on JACK-FLASH C.B.A.
3. DO NOT allow other parts to touch the high voltage circuit on JACK-FLASH C.B.A.
11
DMC-LC1PP / DMC-LC1EB / DMC-LC1EG / DMC-LC1GC / DMC-LC1GD / DMC-LC1GN
7.3. HOW TO DISCHARGE THE CAPACITOR ON JACK-FLASH C.B.A.
CAUTION:
1. Be sure to discharge the capacitor on JACK-FLASH C.B.A.
2. Be careful of the high voltage circuit on JACK-FLASH C.B.A. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of resistor (ERG5SJ102:1k
Ω
/5W).
(an equivalent type of resistor may be used.)
3. Put the resistor between both terminals of capacitor on JACK-FLASH C.B.A. for approx. 5 seconds.
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1
7.4. CLEANING LENS, VIEWFINDER AND LCD PANEL
Do not touch the surface of lens, viewfinder and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the viewfinder and LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their
surface.
surface.
Note:
A lens cleaning paper and lens cleaner are available at local camera shops and market place.
12
DMC-LC1PP / DMC-LC1EB / DMC-LC1EG / DMC-LC1GC / DMC-LC1GD / DMC-LC1GN
Click on the first or last page to see other DMC-LC1PP / DMC-LC1EB / DMC-LC1EG / DMC-LC1GC / DMC-LC1GD / DMC-LC1GN (serv.man2) service manuals if exist.