Panasonic DMC-FP8P / DMC-FP8PC / DMC-FP8PU / DMC-FP8EB / DMC-FP8EE / DMC-FP8EF / DMC-FP8EG / DMC-FP8EP / DMC-FP8GC / DMC-FP8GD / DMC-FP8GH / DMC-FP8GK / DMC-FP8GN / DMC-FP8GT Service Manual ▷ View online
29
(Fig.D19)
8.3.12.
Removal of the Battery Door Unit
(Fig.D20)
NOTE: (When Installing)
Be sure to confirm the following points when installing.
• The Screw is tightened enough.
• Installing conditions are fine. (No distortion, no illegal-
• Installing conditions are fine. (No distortion, no illegal-
space.)
• No dust and/or dirt on every Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient
• LCD image is fine. (No dust and dirt on it, and no gradient
images.)
30
9 Measurements and Adjustments
9.1.
Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-AVC”.
NOTE:
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/
VDBG-AVC”.
NOTE:
After adjustments have been terminated, make sure to achieve “INITIAL SETTINGS”.
NOTE:
*There is no LCD adjustment in this model.
Replaced Part
Adjustment Item
Main
P.C.B.
Top Ope
P.C.B.
Gyro
P.C.B.
VENUS
(IC6001)
Flash-
ROM
(IC6002)
Lens Unit
GYRO
(IC7301/
IC9701)
Camera
Section
Section
OIS hall element adjustment
(OIS)
(OIS)
O
-
-
O
O
O
-
Back focus adjustment,
Gyro adjustment
(BF)
Gyro adjustment
(BF)
O
O
O
O
O
O
O
Shutter adjustment
(SHT)
(SHT)
O
-
-
O
O
O
-
ISO sensitivity adjustment
(ISO)
(ISO)
O
-
-
O
O
O
-
AWB adjustment,
High brightness coloration inspection
(WBL)
High brightness coloration inspection
(WBL)
O
-
-
O
O
O
-
CCD white scratch compensation
(WKI)
(WKI)
O
-
-
O
O
O
-
CCD black scratch compensation
(BKI)
(BKI)
O
-
-
O
O
O
-
Venus zoom inspection
(PZM)
(PZM)
O
-
-
O
O
-
-
Monitor linearity inspection
(MLN)
(MLN)
O
-
-
O
O
O
-
Colour reproduction inspection,
MIC inspection
(COL)
MIC inspection
(COL)
O
-
-
O
O
O
-
31
10 Maintenance
10.1. Cleaning Lens and LCD Panel
Do not touch the surface of lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the its surface.
Note:
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the its surface.
Note:
The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Rear Operation P.C.B. ........................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Schematic Diagram ..................................................... S-5
S4.3. Top Operation Schematic Diagram ....................................... S-6
S4.4. Rear Operation Schematic Diagram ..................................... S-7
S4.5. GYRO Schematic Diagram ................................................... S-8
S5. Print Circuit Board .................................................................... S-9
S5.1. Flash P.C.B. .......................................................................... S-9
S5.2. Top Operation P.C.B. ........................................................... S-10
S5.3. Rear Operation P.C.B. ......................................................... S-11
S5.4. GYRO P.C.B. ....................................................................... S-11
S6. Replacement Parts List. ......................................................... S-13
S7. Exploded View. ....................................................................... S-17
S7.1. Frame and Casing Section.................................................. S-17
S7.2. Packing Parts and Accessories Section (1). ....................... S-18
S7.3. Packing Parts and Accessories Section (2). ....................... S-19
Table of contents
Service Manual
DSC0908052CE
Diagrams and Replacement
Parts List
Vol. 1
(S)...........Silver Type (except PC/EF/GD/GT)
Colour
(K)...........Black Type
(P)...........Pink Type (only PU/GN/GC/GH/GK/GD/GT)
(A)...........Blue Type (only GC/GH/GK/GT)
(R)...........Red Type (except PU/EF/GN/GD)
(N)...........Gold Type (only PC/EE/GH/GK)
(G)...........Green Type (only GC/GH/GK/GD)
(V)...........Violet Type (only GC/GH/GK)
Model No.
DMC-FP8P
DMC-FP8PC
DMC-FP8PU
DMC-FP8EG
DMC-FP8EP
DMC-FP8EF
DMC-FP8EB
DMC-FP8GN
DMC-FP8EE
DMC-FP8GC
DMC-FP8GH
DMC-FP8GK
DMC-FP8GD
DMC-FP8GT
Digital Camera
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK
HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
Click on the first or last page to see other DMC-FP8P / DMC-FP8PC / DMC-FP8PU / DMC-FP8EB / DMC-FP8EE / DMC-FP8EF / DMC-FP8EG / DMC-FP8EP / DMC-FP8GC / DMC-FP8GD / DMC-FP8GH / DMC-FP8GK / DMC-FP8GN / DMC-FP8GT service manuals if exist.