Panasonic WV-CPR460 / WV-CPR464E Simplified Service Manual ▷ View online
WV-CPR460 Series
– 3 –
Referring to Fig. 2-5, remove one screw that secure the
Power Board Unit and I/F Board.
Disconnect the connectors CN402 and CN403 on the
Main Board, and remove the I/F Board.
Disconnect the connector CN404 on the Main Board and
remove the Power Board Unit.
Remove one screw that secure the Earth Lug and
Washer and remove the Earth Lug and Washer (For WV-
CPR460 only).
Power Board Unit and I/F Board.
Disconnect the connectors CN402 and CN403 on the
Main Board, and remove the I/F Board.
Disconnect the connector CN404 on the Main Board and
remove the Power Board Unit.
Remove one screw that secure the Earth Lug and
Washer and remove the Earth Lug and Washer (For WV-
CPR460 only).
Fig. 2-6
Reconnect the CN1 and CN8 on the I/F Board to the
CN402 and CN403 on the Main Board.
Reconnect the connectors by using the Extension Cable
(Refer to Fig. 1-1), between CN404 on the Main Board
and CN101 on the Power Board Unit for Adjustment.
CN402 and CN403 on the Main Board.
Reconnect the connectors by using the Extension Cable
(Refer to Fig. 1-1), between CN404 on the Main Board
and CN101 on the Power Board Unit for Adjustment.
Referring to Fig. 2-4, remove one screw that secure the
Front Unit.
Disconnect the Connector CN401 on the Main Board and
remove the Flexible Board Ass’y and Front Unit for the
Head Optical Ass’y Replacement.
Front Unit.
Disconnect the Connector CN401 on the Main Board and
remove the Flexible Board Ass’y and Front Unit for the
Head Optical Ass’y Replacement.
Remove one screw
Front Unit
Referring to Fig. 2-6, remove four screws that secure the
Main Board and remove the Main Board from the Main
Chassis.
Main Board and remove the Main Board from the Main
Chassis.
Fig. 2-5
Remove
one screw
one screw
CN402
Main
Board
Board
CN404
Earth
Lug
Earth
Lug
Washer
Remove
one
screw
one
screw
CN101
CN1
Power
Board
Unit
Board
Unit
I/F Board
Remove
one screw
one screw
CN402
Main
Board
Board
CN404
CN101
CN1
Power
Board
Unit
Board
Unit
I/F Board
(WV-CPR460)
(WV-CPR464E)
Remove four screws
Main Chassis
Main Board
Flexible Board Ass’y
CN401
Fig. 2-4
Fig. 3-1
Remove two screws
Front Unit
Head Optical Ass’y
3. Head Optical Ass'y Replacement
Procedure
Disassemble the Front Unit of the Camera while referring to
the item 2. Disassembling Procedure for Adjustment.
Referring to Fig. 3-1, disconnect the Connector on the
Head Optical Ass’y and remove the Flexible Board Ass’y.
Remove two screws that secure the Head Optical Ass’y
on the Front Unit and remove the Head Optical Ass’y on
the Front Unit.
Replace Head Optical Ass'y with new one.
the item 2. Disassembling Procedure for Adjustment.
Referring to Fig. 3-1, disconnect the Connector on the
Head Optical Ass’y and remove the Flexible Board Ass’y.
Remove two screws that secure the Head Optical Ass’y
on the Front Unit and remove the Head Optical Ass’y on
the Front Unit.
Replace Head Optical Ass'y with new one.
Connector
Flexible Board
Ass’y
Ass’y
CN403
CN403
CN8
CN8
4. Connection and Setting Up for
Adjustment
4.1. Connection
The Fig. 4-1 shows the connecting diagram for the adjust-
ment procedure.
ment procedure.
Fig. 4-1
Test Chart
Lens
Lcm
Floppy
Disk
Disk
Under scanned
Colour
Video Monitor
Colour
Video Monitor
Video Signal Generator
Remote E.V.R.
Adjustment
Kit
12V DC
Power Supply
Power Supply
RS-232C
Straight
Cable
Straight
Cable
Conversion
Cable
Cable
Personal
Computer
Computer
75
Ω
CAMERA
Waveform
Monitor
Monitor
Vectorscope
CAMERA
IN
VIDEO
OUT
VIDEO
OUT
GEN-LOCK
12V DC or 24V AC
Power Supply
Power Supply
220-240V AC (for WV-CPR460)
(for WV-CPR464E)
– 4 –
WV-CPR460 Series
4.2. Setting Up for New E.V.R. Adjustment
Kit
< Remote E.V.R. Adjustment Kit >
REMOTE
OPERATE
PROG
ALARM
RESET
RESET
NORMAL
SYSTEM
ALARM OFF
EVR
Left
Switch
Switch
Right
Switch
Switch
Mode Selection
Switch
Switch
Program
Switch
Switch
Up
Switch
Switch
Down
Switch
Switch
Set
Switch
Switch
IN
OUT
STD. CAMERA
VP CAMERA
VIDEO
CAMERA
DC12V IN
RS232C
VP/STD Camera Selection Switch
RS232C Connector
< Switch Setting >
Remove the Upper Cover.
Set the switch SW3 on the board to the position as shown
below.
Set the VP/STD Camera Selection Switch on the rear
panel according to the camera.
Set to VP Camera position for VP Multiplexed Camera.
Set to STD Camera position for Standard Camera.
< Installing E.V.R. Adjustment Program >
Make a copy of following necessory files to your comput-
er from original floppy disk of the Remote E.V.R.
Adjustment Kit.
er from original floppy disk of the Remote E.V.R.
Adjustment Kit.
RADJ.EXE
CPR460E.SEQ
CPR460E.EVR
1. Confirm that the CONFIG.SYS file on your computer
contains DEVICE=ANSI.SYS.
2. Insert floppy disk containing E.V.R.adjustment program
into your floppy drive (for example,drive:A) and type A:
3. At the prompt, type CD IBMPC and press ENTER key.
4. Type COPY RADJ.EXE B: and press ENTER key.
5. Type CD\ and press ENTER key.
6. Type CD PAL and press ENTER key.
7. Type COPY CPR460E.SEQ B: and press ENTER key.
8. After completing installation of program, you are ready
to use the E.V.R. adjustment program.
<Rear>
<Front>
Board
SW3
ON
<SW3>
<SW3>
1
2
3
4
Select switch #2 to ON (PAL) or OFF (NTSC) position.
#
ON
OFF
1
FIX
2
PAL
NTSC
3
FIX
4
FIX
WV-CPR460 Series
– 5 –
4.3. Setting Up
An initial setting of the Switches on the Left side Panel of
the WV-CPR460 and WV-CPR464E are as follows:
Gen-Lock Termination Switch
the WV-CPR460 and WV-CPR464E are as follows:
Gen-Lock Termination Switch
(Hi-Z-G/L 75
Ω
)
. . . . . . . . . . . . . .
G/L 75
Ω
RS-485 Temination Switch
(Hi-Z-DATA TERM)
(Hi-Z-DATA TERM)
. . . . . . . . . . .
DATA TERM
Full-Duplex/Half-Duplex Selection Switches
(4-LINE-2-LINE)
(4-LINE-2-LINE)
. . . . . . . . . . . . . . .
2-LINE
The adjustments should be done with this initial setting,
unless otherwise specified.
unless otherwise specified.
The adjustments should be done after 10 minutes warm
up.
up.
5. Adjustment Procedure
<Adjustment Procedure-1>
1. Flange-back Adjustment
Test Point:
CN2 (Video Output Connector)
I/F Board
Adjust:
Flange-back Adjusting Ring
Mount the ALC Lens WV-LA9C3B on the Camera.
Set the Radiation Chart.
Aim the Camera at the Radiation Chart distance of 10m.
Set the Lens Focus Ring so that the Lens Focus positions
approx. 9mm in front from infinity.
Referring to Fig. 5-1, loosen the Focus-Fixing Screw that
secure the Flange-back Adjusting Ring.
Adjust the Flange-back Adjusting Ring to obtain best
focal point.
Set the Radiation Chart.
Aim the Camera at the Radiation Chart distance of 10m.
Set the Lens Focus Ring so that the Lens Focus positions
approx. 9mm in front from infinity.
Referring to Fig. 5-1, loosen the Focus-Fixing Screw that
secure the Flange-back Adjusting Ring.
Adjust the Flange-back Adjusting Ring to obtain best
focal point.
Fig. 5-1
Focus-Fixing Screw
Flange-back
Adjusting Ring
Tighten the Focus-Fixing Screw that secure the Flange-
back Adjusting Ring carefully.
Change the ALC Lens to WV-LA9C3A from WV-LA9C3B.
back Adjusting Ring carefully.
Change the ALC Lens to WV-LA9C3A from WV-LA9C3B.
<Adjustment Procedure-2>
(E.V.R. Adjustment)
Insert new disk containing the E.V.R. Adjustment pro-
gram into IBM PC/AT.
To change communication mode of the camera, turn off
the power for the camera.
Turn on the power for the camera while pressing both
Left and Right Buttons on the Left side panel of the cam-
era.
At the prompt, type RADJ CPR460E and press the
ENTER key, an initial menu will be displayed in Table 5-1.
gram into IBM PC/AT.
To change communication mode of the camera, turn off
the power for the camera.
Turn on the power for the camera while pressing both
Left and Right Buttons on the Left side panel of the cam-
era.
At the prompt, type RADJ CPR460E and press the
ENTER key, an initial menu will be displayed in Table 5-1.
Press the SAVE(F5) key of the Computer, then the
Computer will ask you for the file name.
Give appropriate file name to the Computer. But do not
use CPR460E.EVR for your file.
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
Press the LOAD(F1) key and type CPR460E.EVR and
press the ENTER key for presetting adjustment of the
Camera.
Computer will ask you for the file name.
Give appropriate file name to the Computer. But do not
use CPR460E.EVR for your file.
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
Press the LOAD(F1) key and type CPR460E.EVR and
press the ENTER key for presetting adjustment of the
Camera.
Notes:
Adjustment items are exactly same as WV-CP460 Series.
Difference point is just file name.
Please kindly refer original manual.
Difference point is just file name.
Please kindly refer original manual.
Table 5-1
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM (C) MCI Co. CCTV PRODUCT:CPR460 EEPROM:0
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
MENU
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
Page (1/1)
✽ ✽ ✽ ✽ ✽
PAL
1.1. SC FREQUENCY
1.2. VS SC FREQUNCY
2. HI CLIP LEVEL
3. ALC DC
4. VIDEO OUT GAIN
5. PEDESTAL
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. WB 3200K MANU OFFSET R
7.2. WB 3200K MANU OFFSET B
8.1. WB 6500K ATW LIMIT R
8.2. WB 6500K ATW LIMIT B
9.1. 3200K R_GAIN
9.2. 3200K B_GAIN
9.3. 3200K MATRIX
10.1. 5100K R_GAIN
10.2. 5100K B_GAIN
11. HI LIGHT CHROMA CLIP
<CONTENTS>
1.2. VS SC FREQUNCY
2. HI CLIP LEVEL
3. ALC DC
4. VIDEO OUT GAIN
5. PEDESTAL
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. WB 3200K MANU OFFSET R
7.2. WB 3200K MANU OFFSET B
8.1. WB 6500K ATW LIMIT R
8.2. WB 6500K ATW LIMIT B
9.1. 3200K R_GAIN
9.2. 3200K B_GAIN
9.3. 3200K MATRIX
10.1. 5100K R_GAIN
10.2. 5100K B_GAIN
11. HI LIGHT CHROMA CLIP
<CONTENTS>
17734470 + - 40Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD (F1) QUIT (F3) SAVE (F5)
– 6 –
WV-CPR460 Series
WIRING DIAGRAM
8
40 39
2 1
2
1
CN404
CN101
CN401
39 40
1 2
CN1
7
1
19
20
CN402
2
1
20
CN1
MAIN BOARD
RS485
BOARD
BOARD
POWER BOARD UNIT(PCB5)
SENSOR
BOARD
BOARD
HEAD OPTICAL
ASS'Y (M101)
ASS'Y (M101)
I/F BOARD
1
8
CN8
VIDEO OUT
AC INLET
SOCKET
(WV-CPR460)
SOCKET
(WV-CPR460)
AC/DC COMPATIBLE
INPUT TERMNAL
[DC12V IN/AC24V IN]
(WV-CPR464E)
INPUT TERMNAL
[DC12V IN/AC24V IN]
(WV-CPR464E)
GEN-LOCK
CN4
CN2
1
5
CN7
1
5
E1
E2
E1
(CPR46J1A)
(CPR46J1A)
RS485
1
7
8
CN403
2
1
CN6
AUTO IRIS
LENS
CONNECTOR
AUTO IRIS
LENS
CONNECTOR
FB1
FLEXIBLE
BOARD ASS'Y
(VCP16JKZ1A)
FLEXIBLE
BOARD ASS'Y
(VCP16JKZ1A)
3
4
2
Click on the first or last page to see other WV-CPR460 / WV-CPR464E service manuals if exist.