DOWNLOAD Panasonic BB-HCM511CE / BB-HCM531CE Service Manual ↓ Size: 5.07 MB | Pages: 98 in PDF or view online for FREE

25

1. Screw the threaded mount into the stand/tripod mounting

hole.

2. Turn the grip firmly.

Wiring without making a hole for a cable in the ceiling or
wall
For BB-HCM531:
Before following the procedures below, we recommend passing
all cables (AC adaptor, LAN, audio/video, etc.) through a duct
(i.e., hose, tube, etc.) for proper waterproofing.

1. Secure the safety wire to the camera using screw A 

(included) and washer S (included).

•Make sure you attach the safety wire when mounting the 

camera, to prevent the camera from falling.

2. Remove the tab on the flexible stand. Then pass the cables

through the notch.

3. For BB-HCM511:

Connect all necessary cables (AC adaptor, LAN, audio/
video, etc.). Then skip to step 7.

For BB-HCM531:
Pass the cables through the connector cover, and then 
connect all necessary cables (AC adaptor, LAN, audio/
video, etc.). Attach the connector cover by fastening the 
two screws.

4. Attach the sunshade by fastening the two screws.

5. Wrap the cables in the included foam strip and insert the

foam strip into the opening of the connector cover.

• Leave about 10 mm of the foam exposed, as shown.

6. Wrap the first 20 cm of the cables (starting with the connec-

tor cover) using the included self bonding tape. Make sure
to wrap the opening of the connector cover thoroughly
(three or four times).

• Stretch the tape to twice its length when you wrap the

cables.

• Overlap the tape when you wrap the cables.

26

7. Attach the camera by screwing the threaded mount into the

stand mounting hole.

8. Mount the flexible stand firmly to the ceiling or wall with

screw B (included).

• Do not drive the screws into a soft material. Drive the

screws into a secure area of the wall, such as a column,
otherwise the camera may fall and be damaged.

• Use screws that are suited for the type of material the

camera is mounted to.

• Be careful not to nip the cables.
• Make sure the flexible stand is firmly mounted on a beam

of wood (25 mm and greater) etc. When there is no
beam, apply a board on the other side of the ceiling or
wall to make sure the camera does not drop.

9. Adjust the camera position and tighten the flexible stand

grip firmly.

• Confirm that the cords have been waterproofed and that

the portion of the cord protruding from the flexible stand
is wrapped in self bonding tape, as shown in (A) below.

10. Secure the safety wire to the ceiling or wall using screw B

(included) and washer L (included).

• Leave some slack in the safety wire, as shown.
• Make sure the safety wire is firmly mounted on a beam of

wood (25 mm and greater) etc. When there is no beam,
apply a board on the other side of the ceiling or wall to
make sure the camera does not drop.

• Make sure to waterproof the opening of the duct so that

water does not enter it.

Wiring through a hole made in the ceiling or wall
For BB-HCM511: (INDOOR USE ONLY)
Make a hole for cables in the ceiling or wall. Secure the safety
wire to the camera and pass the cables through the notch.
Then follow steps 7, 8, 9 and 10.

• Prepare anchors for 4 mm diameter screws for mounting.

1. Place the flexible stand on the ceiling or wall where you

plan to mount the flexible stand and mark the points where
you are going to make holes.

2. Make holes with an electric drill. Insert anchors (customer-

provided) into the holes and push them inside the holes
with a hammer.
•Mortar ceilings or walls break easily when drilling. Be 

careful of pieces of mortar which may become loose and
fall.

3. Mount the flexible stand using the screws.

27

A : Other Function Check (P.28)
B : Power Supply Block Check (P.29)
C : CPU Peripheral Block Check (P.30)
D : Image Block Check (P.31)
E : Audio Block Check (P.32)
F : LAN Block Check (P.34)

K : LED Circuit Check (P.39)
L : Diagnosis NG Check (P.40)
M : Version Upgrade Check (P.41)

28

D : Image Block Check (P.31)
G : Motor Block Check (P.35)
H : I/O Terminal Check (P.36)
I : SD Card Block Check (P.37)

J : RTC Circuit Check (P.38)