Panasonic SC-HTX500EB / SC-HTX500EEK / SU-HTX500EB / SU-HTX500EE Service Manual ▷ View online
21
6 Self diagnostic and special mode setting
This unit is equipped with features of self-diagnostic & special mode setting for checking the functions & reliability.
Special Note : Checking of the reliability (ageing) & changer operation must be carry out to ensure good working condi-
tion in unit.
tion in unit.
6.1.
Automatically Displayed Error Codes
An error code automatically appears on the display (LCD) when faulty operation is detected. Refer to Fig 7.1
Fig 7.1
6.1.1.
Display Details
Refer to the following table.
LCD Display
Symptom
Cause and Remedy
OVERLOAD (F61)
Speaker short, amplifier failure, electrical
overload etc.
overload etc.
Speaker short and failure in power amplifier, pre-
amplifier circuits. Check for faulty parts and replace
with new parts if necessary.
amplifier circuits. Check for faulty parts and replace
with new parts if necessary.
Humidity protection activated
FANLOCK
Fan stopped
Failure fan and fan control circuits. Check for faulty
parts and replace with new parts if necessary.
parts and replace with new parts if necessary.
F70
Communication error between sub micro- pro-
cessor and its peripheral LSI
cessor and its peripheral LSI
Failure sub-micro processor and its peripherals LSI.
Check for faulty parts and replace with new parts if
necessary.
Check for faulty parts and replace with new parts if
necessary.
F76
When the power is turned on, the unit power
automatically turns off; the power cannot be
turned on.
automatically turns off; the power cannot be
turned on.
Failure in the power circuit system of the unit. This
may happen when the direct current electricity is sup-
plied to speaker terminals. Check that the speaker
wires are not shorted (bare wire touching each other)
or that the unit is in a hot enviroment without proper
ventillation.
may happen when the direct current electricity is sup-
plied to speaker terminals. Check that the speaker
wires are not shorted (bare wire touching each other)
or that the unit is in a hot enviroment without proper
ventillation.
U30 REM1
U30 REM2
U30 REM2
The main unit has a different code setting
from the remote control
from the remote control
Set the same remote control code for this system and
remote control.
remote control.
• If “REMOTE 2” is displayed, set remote control
code to “2”.
• If “REMOTE 1” is displayed, set remote control
code to “1”.
U701
The equipment connected by the HDMI cable
is not compatible with this system’s copyright
protection technology.
is not compatible with this system’s copyright
protection technology.
Connect equipment that is compatible with this sys-
tem’s copyright protection technology.
tem’s copyright protection technology.
U704
The system is receiving video signals that are
incompatible with it through HDMI connection.
incompatible with it through HDMI connection.
Check the settings of the connected equipment.
U703
A problem has occurred with the HDMI con-
nection.
nection.
Try the following to correct the problem. Consult your
dealer if the error code remains on the display.
dealer if the error code remains on the display.
• Turn the connected equipment off and on again.
• Disconnect the HDMI cable then reconnect it.
• Do not connect more than 2 equipment in series to
• Disconnect the HDMI cable then reconnect it.
• Do not connect more than 2 equipment in series to
the output of this system.
NOT POSSIBLE FOR THIS INPUT
SOURCE
(Scrolling)
SOURCE
(Scrolling)
Dolby Virtual Speaker, Dobly Pro Logic II and
SFC are used for dual sounds.
SFC are used for dual sounds.
You cannot use Dolby Virtual Speaker, Dolby Pro Logic
II and SFC for dual sounds.
II and SFC for dual sounds.
NOT POSSIBLE FOR THIS PCM
SOURCE
(Scrolling)
SOURCE
(Scrolling)
Dolby Virtual Speaker, Dolby Pro Logic and
SFC effect with PCM signals are use with
sampling frequency over 48 kHz.
SFC is used for multi-channel LPCM signal.
SFC effect with PCM signals are use with
sampling frequency over 48 kHz.
SFC is used for multi-channel LPCM signal.
You cannot use Dolby Virtual Speaker, Dolby Pro Logic
and SFC effect with PCM signals with sampling fre-
quency over 48 kHz.
SFC is not available for multi-channel LPCM signal.
and SFC effect with PCM signals with sampling fre-
quency over 48 kHz.
SFC is not available for multi-channel LPCM signal.
22
6.2.
Service Mode
This mode can be used during servicing.
1. Plug the AC cord to the power source. Press and hold down the [VOL +] button and the [VOL -] button, and then press the
[POWER] button at the same time.
2. The message, [SERVICE] appears on the display for three seconds, and then it will display the following. Refer to Fig 7.2
Fig 7.2
3. To confirm the mP software version: When [VOL +] button is pressed, [M--- ****] is displayed [---] is current main micon ver-
sion; [****] is current checksum. If no ROM correction, [NO] is displayed.
When [VOL -] is pressed, display [H***], [***] is current version of HDMI micon.
Ruturning to Normal Display
Press the [POWER] button on the unit to exit the function. The power is turned off.
Press the [POWER] button on the unit to exit the function. The power is turned off.
6.3.
Checking 2.1 ch output of analog signal
This function can be used to specify which channel is faulty if the speaker output malfunction is found.
This is also useful to analyze the faulty channels on the circuits.
This is also useful to analyze the faulty channels on the circuits.
When [TEST] button on the remote control is pressed in the Doctor Mode, All CH Output Mode is turned on.
In this mode, analog signal input to the L channel of VCR is output to all the channels.
In this mode, analog signal input to the L channel of VCR is output to all the channels.
Ruturning to Normal Display
Press the [POWER] button on the unit to exit the function. The power is turned off.
Press the [POWER] button on the unit to exit the function. The power is turned off.
6.4.
Doctor Mode
This mode can be used during servicing.
1. Plug the AC adapter to the power source. Press and hold down the [INPUT SELECTOR] button and the [VOL +] button, and
then press the [POWER] button at the same time.
2. The message, “_DOCTOR_” appears on the display for three seconds, and then it will display the following. Refer to Fig 7.3
23
Fig 7.3
Ruturning to Normal Display
Press the [POWER] button on the unit to exit the function. The power is turned off.
Press the [POWER] button on the unit to exit the function. The power is turned off.
6.5.
Test Mode
Test mode function at some remote control codes as below table.
Fig 7.4
Ruturning to Normal Display
Press the [POWER] button on the unit to exit the function. The power is turned off.
Press the [POWER] button on the unit to exit the function. The power is turned off.
Remote Control
Test Mode Function and settings
Selector
Sound Mode
other settings
Vol/Tone
SPEAKER LEVEL
-
AUX 4
STEREO
ANALOG
-18dB/0dB
SPEAKER LEVEL
CH
AUX 3
STEREO
E2: OPT 2
Others: ANALOG
-18dB/0dB
OK
TV
STEREO
DIGITAL (OPT 1)
-48dB/0dB
SFC MUSIC
AUX 2
STEREO
DIGITAL (E2: COAX
Others: OPT 2)
-48dB/0dB
MUTE
All indicators of FL are displayed. All LED are off. Refer to Fig 7.4
Note : After this setting, only ‘POWER’ button can be activated.
Note : After this setting, only ‘POWER’ button can be activated.
Volume Up
Check Main mP software version.
Display [M---- ****], [----] is current version; **** is current checksum. If no ROM correction, [NO] is displayed.
Volume is still increased but not displayed.
Display [M---- ****], [----] is current version; **** is current checksum. If no ROM correction, [NO] is displayed.
Volume is still increased but not displayed.
Volume Down
Check Main mP software version.
Display [H ****], [***] is current version.
Volume is still increased but not displayed.
Display [H ****], [***] is current version.
Volume is still increased but not displayed.
TEST
AUX 4 (ANALOG)
VS
All CH Output Mode
-18dB/0dB
TV (OPT 1)
STEREO
Balance is set to leftmost.
-18dB/0dB
TV (OPT 1)
STEREO
Balance is set to rightmost.
-18dB/0dB
24
7 Troubleshooting Guide
7.1.
HDMI Troubleshooting Guide
1. Connection of HDMI system.
2. Check of HDMI Sound (Dolby Digital Signal)
• Play back a track with signal 96kHz, 5.1ch. Check the Level and Noise output from L / R / SUBW speaker or pin..
• Play back a track with signal 192kHz, 2ch), If this source can be reproduced, it is OK.
• Play back a track with signal 192kHz, 2ch), If this source can be reproduced, it is OK.
3. Check of HDMI Picture
• The picture quality of TV is checked using DVD disc with the colour bar signal.
• [DVD TEST DISC S-20] - Track No. 2 (Flag of the rising sun)
• [DVD TEST DISC S-20] - Track No. 2 (Flag of the rising sun)
[Colour bar disc] - Colour bar signal.
• Make on DVD Setup Picture
Comfirmed that there are neither distortion nor noise on the screen.
• If it is a picture quality equal when DVD was connected directly to TV, it is OK
1. Connect directly DVD player to TV.
2. Connect DVD player to set then connect it to TV.
3. Do the comparison for (1) and (2) if same, it is OK.
2. Connect DVD player to set then connect it to TV.
3. Do the comparison for (1) and (2) if same, it is OK.
Click on the first or last page to see other SC-HTX500EB / SC-HTX500EEK / SU-HTX500EB / SU-HTX500EE service manuals if exist.