Panasonic SA-VK660EE / SC-VK660EE Service Manual ▷ View online
37
SA-VK660EE
9.4.6. Mechanism Error Code Table
Error
Code
H01
Mode switch
Detection of switch for "On" when the
For Deck Mechanism
abnormal (Plunger
deck mechanism is in the driving
Unit (Deck 1/2).
and capstan motor)
mode. Detection time at 1.6ms in 6
Press [ STOP] on the
times interval.
main unit for next error.
To exit, press
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
To exit, press
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
H02
REC_INHF switch
Detection of switch for presence of the
For Deck Mechanism
abnormal
FORWARD recording tab when a
Unit (Deck 1/2).
cassette is loaded into the deck.
Press [ STOP] on the
Detection time is 20ms at 2 times
main unit for next error.
interval.
To exit, press
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
H03
HALF switch
Detection of switch for "ON" state
For Deck Mechanism
abnormal
when a casstte is loaded into the deck.
Unit (Deck 1/2).
Detection time is 20ms at 2 times
Press [ STOP] on the
interval. When no cassette is loaded,
main unit for next error.
it shall be in "OFF" state.
To exit, press
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
F01
Reel pulse abnormal Detection of switch for the reel pulse
For Deck Mechanism
signal toggling between high and low.
Unit (Deck 1/2).
Press [ STOP] on the
main unit for next error.
To exit, press
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
Press [ STOP] on the
main unit for next error.
To exit, press
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
F02
TPS abnormal
Tape position detection signal. It is
For Deck Mechanism
abnormal condition when the tape
Unit (Deck 1/2).
ends before the checking is
Press [ STOP] on the
completed.
main unit for next error.
To exit, press
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
To exit, press
[POWER] button on
the main unit. Normal
operation shall be
executed upon next
powering on of the
main unit.
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
38
SA-VK660EE
9.5. Sales Demostration Lock Function
This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject
function.”LOCKED” is displayed on the main unit, and ordinary operation is disabled.
function.”LOCKED” is displayed on the main unit, and ordinary operation is disabled.
9.5.1. Setting
•
•
•
•
Prohibiting removal of disc
At POWER ON, condition, press and hold [STOP} button and the power button on the main unit for at least three seconds. (The
message, “_ _ _ LOCKED_” appears when the function is activated.)
message, “_ _ _ LOCKED_” appears when the function is activated.)
Note:
“OPEN/CLOSE” and “DISC EXCHANGE” buttons are invalid and the main unit displays “_ _ _LOCKED_” while the lock function
mode is entered.
mode is entered.
•
•
•
•
Prohibiting operation of selector and disc
At POWER ON condition, press and hold [>] button and the power button on the main unit for at least three seconds. (The
message, “_ _ _ LOCKED_” appears when the function is activated.)
message, “_ _ _ LOCKED_” appears when the function is activated.)
Note:
The following buttons are invalid and the main unit displays “_ _ _LOCKED_” while the lock function mode us entered.
9.5.2. Cancellation
The lock can be cancelled by the same procedure as used in setting. (“UNLOCKED” is displayed on cancellation. Disconnecting
the power cable from power outlet does not cancel the lock.)
the power cable from power outlet does not cancel the lock.)
9.6. Service Precautions
9.6.1. Recovery after the main unit is repaired
•
•
•
•
When the FLASH ROM IC (IC8651) or DVD Module P.C.B. is replaced, carry out the recovery processing to optimize the drive.
Playback the recovery disc to process the recovery automitically.
•
•
•
•
Recovery disc (Product number: RFKZD03R005)[SPG]
•
•
•
•
Performing recovery process
1. Load the recovery disc FKZD03R005 on to the main unit and run it.
2. Recovery is performed automatically. When it is finished, a message appears on the screen.
3. Remove the recovery disc.
4. Turn off the power.
5. Initialize the main unit.
9.6.2. Firmware version-up of the DVD player
•
•
•
•
The firmware of the DVD player may be renewed to improve the quality including operability and playability to the substandard
disc process to optimize the drive.
disc process to optimize the drive.
The recovery disc has also firmware version-up.
•
•
•
•
After version-up, recovery processing is executed automatically.
•
•
•
•
Part number of the recovery disc for version-up will be noticed when it is supplied.
•
•
•
•
Updating firmware
1. Load the recovery disc on to the player and run it.
2. Firmware version of the player is automatically checked. Appropriate message appears whenever necessary.
3. Using remote controller’s cursor key, select whether version updating is to be done or not. (Selection of Yes/No)
4. a. If Yes is selected, version updating is performed.
b. If No is selected, only recovery disc is performed.
5. a. When updating is finished, remove the disc according to the message appearing on the screen.
39
SA-VK660EE
b. Remove the disc according to the message appearing on the screen.
6. Turn off the power.
Note:
If the AC power supply is shut out during version-up due to power failure, the version-up is improperly carried out.
In such case, replace the FLASH ROM IC (IC8651) and carry out the version-up again.
9.6.3. DVD Module P.C.B. reset
•
•
•
•
When after replacing FLASH ROM IC or DVD Module P.C.B., FL displays error code “DVD F897”. This means the unit is not
initialized properly and the following process needs to be carry out.
initialized properly and the following process needs to be carry out.
•
•
•
•
Procedures:
1. Press
on remote control while pressing “STOP” button on the main unit. (To enter into initialization)
2. FL display show “INIT”.
3. While still pressing “STOP” button on main unit, press “ENTER” on remote control . (To reset the unit)
4. FL wll display “RESET” before FL display will change to TOC reading again.
5. Power off unit. Unplug the AC cord.
6. Power on the unit. It should be no problem. If problem persist check on the DVD Module P.C.B. or FLASH ROM IC.
40
SA-VK660EE
Click on the first or last page to see other SA-VK660EE / SC-VK660EE service manuals if exist.