Panasonic SA-VK480EE / SC-VK480EE Service Manual ▷ View online
33
6.5.
DVD Self Diagnostic Function-Error Code
6.5.1.
DVD Module Error Code Table
Error
Code
U702 HDMI/DVI I2C
The communication error of I2C when
Press [ STOP] on main
communication error
connecting it with HDMI/DVI. For
unit for next error.
instance, when EDID information to which
information on the TV set side has been
described cannot be read, it is generated.
U703 HDMI/DVI attestation
When attestation (HDCP) with the TV
Press [ STOP] on main
error
side fails when connecting it with
unit for next error.
HDMI/DVI, it is generated.
U704 HDMI/DVI SRM
It is generated at the equipment to which
Press [ STOP] on main
Riborcerar
the TV set is Riborced when connecting it
unit for next error.
with HDMI/DVI.
U705 HDMI/DVI SRM disk
It is generated at the time of it is time
Press [ STOP] on main
falsification check
when illegal the SRM data of the
unit for next error.
error
reproducing disk (verify error), when
connecting it with HDMI/DVI.
F740 HDMI device key
I2C error when writing HDMI Key device
Press [ STOP] on main
into transmitter.
unit for next error.
F893 FLASH ROM IC data
Firmware error, DV5.0 LSI IC (IC8651)
Press [ STOP] on main
falsification error
error.
unit for next error.
F894 EEPROM IC
When failing in the access to EEPROM
Press [ STOP] on main
abnormality error
IC located in the DVD Module P.C.B.
unit for next error.
(IC8611).
F895 Language area
Firmware version agreement check for
Press [ STOP] on main
abnormal
factory preset setting failure prevention.
unit for next error.
F897 Initialization
Incomplete initialization after writing of
Press [ STOP] on main
error
new firmware (Factory preset setting
unit for next error.
failure prevention)
F899 The communication
Unsuitable combination of number of
Press [ STOP] on main
specification
system com and panel com used.
unit for next error.
disagreement
(Frimware)
between
micro-processor
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
34
6.5.2.
DVD Mechanism Unit (CR14D) Error Code Table
Error
Code
H01 Tray loading error
The tray opening and closing is
Press [ STOP] on
abnormal. CLOSE and OPEN of the
main unit for next error.
tray cannot be carried out properly.
(OPEN time: OPEN
Loading motor error, DV5 LSI IC
CLOSE OPEN
(IC8001) error.
H01 at CLOSE: CLOSE
OPEN CLOSE
H01)
OPEN CLOSE
H01)
H02 Spindle servo error
The spindle servo/motor is abnormal.
Press [ STOP] on
The FG pulse is abnormal. CLV servo
main unit for next error.
error.
H03 Traverse servo error The traverse is abnormal. (Traverse
Press [ STOP] on
servo, DV5 LSI IC (IC8001), TRV
main unit for next error.
motor error.)
H04 Tracking servo error Tracking coil NG (OPU unit
Press [ STOP] on
abnormal), DV5 LSI IC (IC8001)
main unit for next error.
error.
H05 Seek time out error
It is not possible to access the disc.
Press [ STOP] on
TOC cannot read. Abnormal disc etc.
main unit for next error.
Pickup abnormal or disk is dirty.
(TRV motor error, DV5 LSI IC
(IC8001) error.)
(TRV motor error, DV5 LSI IC
(IC8001) error.)
H07 Driver IC thermal
The spindle motor is abnormal. (short
Press [ STOP] on
shut down
between brushes)
main unit for next error.
H15 Disc tray open
The disc tray cannot be opened & it
Press [ STOP] on
detection switch
closes spontaneously.
main unit for next error.
failure
H16 Disc tray close
The disc tray cannot be closed & it
Press [ STOP] on
detection switch
opens spontaneously.
main unit for next error.
failure
U11 Focus servo error
Focus coil, FE signal error.
Press [ STOP] on
main unit for next error.
(Unfinalized DVD-R
main unit for next error.
(Unfinalized DVD-R
U15 Unfinalized DVD-R
is likely to beocme U11.)
F500 DSC error
DV5 LSI IC (IC8001) stops in the
Press [ STOP] on
occurance of servo error (startup,
main unit for next error.
focus error, etc)
F506 Invalid media
Disc is flipped over, TOC unreadable,
Press [ STOP] on
incompatible disc.
main unit for next error.
F620 OPU unit
Laser protection at high temperature.
Press [ STOP] on
abnormality
main unit for next error.
temperature
F621 OPU unit
Laser protection at circuit failure.
Press [ STOP] on
circuitry
main unit for next error.
temperature
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
35
6.5.3.
Power Supply & Digital Amplifier Error Code Table
6.5.4.
USB Error Code Table
Error
Code
F61
The abnormalities
In normal operation, when DCDET2 goes
Press [ STOP] on main
in an output or power
to "L" (Low) (Not during POWER OFF
unit for next error.
supply circuit of
condition), F61 appears on FLDisplay
POWER AMP
for 1 second and PCONT goes to
"L" (Low).This is due to speaker output
has DC voltage or fan is not working.
F76
Abnormality in the
In normal operation when DCDET1 is
Press [ STOP] on main
output voltage of
detected "L" (Low) for two consecutive
unit for next error.
stabilized power
times, F76 is displayed on FL for
supply
1 second and after that PCONT will be
turned to "L" (Low). This is due to any of
the DC voltages (+9V, +7V, -7V, +5V,
+5.3V etc.) C22 not available.
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
Error
Code
F650 USB device: Devices
Devices other than the mass storage
Press [ STOP] on main
other than mass
class are connected.
unit for next error.
storage
F651 USB device: Non-Full
The device that the transfer rate did not
Press [ STOP] on main
Speed Device
correspond to Full Speed was
unit for next error.
connected.
F652 USB device:
The device in the interface (subclass)
Press [ STOP] on main
Interface NG
outside correspondence was connected.
unit for next error.
(correspondence interface)
001b: Reduced Block Commands (RBC)
010b: SFF-8020i. MMC-2 (ATAPI)
110b: SCSI transparent command set.
F655 USB device:
The overcurrent of 500mA or more was
Press [ STOP] on main
Overcurrent detection
detected in VDD USB, and the USB
unit for next error.
device driver function was intercepted.
(To intercept the current.)
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
36
6.5.5.
DVD Changer Mechanism Unit (CR14D) Error Code Table
Error Code Diagnosis Contents Description of error
Automatic FL Display
Remarks
LOAD
Load operation faulty The load operation cannot
complete
occurs.
occurs.
occurs.
occurs.
occurs.
occurs.
when time out
For DVD Mechanism unit (CR14D).
For DVD Mechanism unit (CR14D).
For DVD Mechanism unit (CR14D).
For DVD Mechanism unit (CR14D).
For DVD Mechanism unit (CR14D).
For DVD Mechanism unit (CR14D).
For DVD Mechanism unit (CR14D).
For DVD Mechanism unit (CR14D).
For DVD Mechanism unit (CR14D).
Press [EXCHANGE] on main unit for
next error.
next error.
UNLD
Unload operation
faulty
faulty
The unload operation
cannot complete when time
out occurs.
cannot complete when time
out occurs.
Press [EXCHANGE] on main unit for
next error.
next error.
UP
Exchange open
operation faulty
operation faulty
The exchange open
operation cannot complete
when time out occurs.
operation cannot complete
when time out occurs.
Press [EXCHANGE] on main unit for
next error.
next error.
DOWN
Down operation faulty The down operation cannot
complete when time out
Press [EXCHANGE] on main unit for
next error.
next error.
OPEN
Open operation faulty The open operation cannot
complete when time out
Press [EXCHANGE] on main unit for
next error.
next error.
CLOSE
Close operation faulty The open operation cannot
complete when time out
Press [EXCHANGE] on main unit for
next error.
next error.
MODEL
Mode change to
updown operation
faulty
updown operation
faulty
The mode change to
updown operation cannot
complete when time out
occurs.
updown operation cannot
complete when time out
occurs.
Press [EXCHANGE] on main unit for
next error.
next error.
Error Code Diagnosis Contents Description of error
Automatic FL Display
Remarks
It changes to
up/down.
MODEH
Mode change to
horizontal operation
faulty
horizontal operation
faulty
The mode change to
horizontal operation cannot
complete when time out
horizontal operation cannot
complete when time out
Press [EXCHANGE] on main unit for
next error.
next error.
INITIALIZE Initialize operation
faulty
The initialize operation
cannot complete.
cannot complete.
Press [EXCHANGE] on main unit for
next error.
next error.
Click on the first or last page to see other SA-VK480EE / SC-VK480EE service manuals if exist.