Panasonic SA-PT560E / SA-PT560EB / SA-PT560EG Service Manual ▷ View online
8 Self-Diagnosis and Special Mode Setting
8.1. Service Mode Summary Table
The service modes can be activated by pressing various button combination on the main unit and remote control unit.
Below is the summary for the various modes for checking:
Main unit buttons
Remote control unit buttons
Application
Note
[STOP]
[0]
Error code check.
(Refer to the section
“8.2.1. Service Mode
Table 1” for more
information.)
“8.2.1. Service Mode
Table 1” for more
information.)
[5]
Jitter checking.
[PAUSE]
Initial setting of laser drive current.
[FUNCTIONS]
DVD laser drive current check.
(Refer to the section
“8.2.2. Service Mode
Table 2” for more
information.)
“8.2.2. Service Mode
Table 2” for more
information.)
[3]
CD laser drive current check.
[6]
Region display and mode.
[SOUND]
CPPM/CRM keys check.
[7]
Micro-processor firmware version check.
(Refer to the section
“8.2.3. Service Mode
Table 3“ for more
information.)
“8.2.3. Service Mode
Table 3“ for more
information.)
[
]
Initialization of the player (factory setting is restored).
Used after replacement of Micro-processor (DV5 LSI) IC,
FLASH ROM IC (IC8651), EEPROM IC (IC8611) and DVD
Module P.C.B.
Used after replacement of Micro-processor (DV5 LSI) IC,
FLASH ROM IC (IC8651), EEPROM IC (IC8611) and DVD
Module P.C.B.
[OK]
DVD Module P.C.B. reset.
[8]
DVD Module P.C.B. firmware version check.
(Refer to the section
“8.2.4. Service Mode
Table 4“ for more
information.)
“8.2.4. Service Mode
Table 4“ for more
information.)
[
]
Timer 1 check.
[
]
Timer 1 reset.
[
]
Timer 2 check.
[
]
Timer 2 reset.
Note:
An error code will be canceled if a power supply is turned OFF.
*1: CPPM is the copy guard function beforehand written in the disk for protection of copyrights.
*2: CEC is the consumer electronic control used for high-level user control of HDMI-connected devices.
*3: HDCP is the specification developed to control digital audio & video contents transmission for DVI or HDMI connections.
8.2. Service Mode Table
By pressing various button combinations on the main unit and remote control unit, you can activate the various service modes for
checking.
checking.
Special Note:
•
•
•
•
Due to the limitations of the no. characters that can be shown on the FL Display, the “FL Display” button on the remote
control unit can be used to show the two display pages. (Display 1 / Display 2).
control unit can be used to show the two display pages. (Display 1 / Display 2).
•
•
•
•
Refer to Section 7.1 for the section on “Remote Control Key Buttons Operations”.
25
SA-PT560E / SA-PT560EB / SA-PT560EG
8.2.1. Service Mode Table 1
Initial setting of
laser drive
current
Jitter check
Jitter check.
Jitter rate is measured and displayed.
Measurement is repeatedly done in
the cycle of one second. Read error
counter starts from zero upon mode
setting.
When target block data failed to be
read out, the counter advances by one
increment. When the failure is caused
by minor error, it may be corrected
when retried to enable successful
reading.
In this case, the counter advances by
one. When the error persists even
after retry, the counter may jump by
two or more.
Jitter rate is measured and displayed.
Measurement is repeatedly done in
the cycle of one second. Read error
counter starts from zero upon mode
setting.
When target block data failed to be
read out, the counter advances by one
increment. When the failure is caused
by minor error, it may be corrected
when retried to enable successful
reading.
In this case, the counter advances by
one. When the error persists even
after retry, the counter may jump by
two or more.
FL Display sequence:
Display 1 2.
Display 1 2.
Jitter rate is shown in decimal notation to one
place of decimal.
Focus drive value is shown in hexadecimal
notation.
place of decimal.
Focus drive value is shown in hexadecimal
notation.
(Display 1)
Jitter rate
Jitter check
mode
mode
(Display 2)
Lead
Error
Counter
Error
Counter
Focus Drive
Value
Value
Press [POWER] or [STOP]
button to exit.
button to exit.
In STOP (with disc inside
tray) mode, press [STOP]
button on the main unit,
and [5] button on
the remote control unit,
after Display 1 appears,
then press [PLAY].
tray) mode, press [STOP]
button on the main unit,
and [5] button on
the remote control unit,
after Display 1 appears,
then press [PLAY].
Press [FL Display] on
remote control unit for next
page (FL Display).
remote control unit for next
page (FL Display).
Error code
check
Error code check
The latest error code stored in the
EEPROM IC is displayed.
The latest error code stored in the
EEPROM IC is displayed.
Note: Refer to "Section 8.3 DVD Self
Diagnostic Function-Error Code" for
more detailed information on the error
codes.
Diagnostic Function-Error Code" for
more detailed information on the error
codes.
Error code (play_err) is expressed in the
following convention.
Error code = 0 x DAXX is expressed:
following convention.
Error code = 0 x DAXX is expressed:
DVDnn U12
Error code = 0 x DBXX is expressed:
DVDnn H12
Error code = 0 x DXXX is expressed:
DVDnn F123
Error code = 0 x 0000 is expressed:
DVDnn F---
* "xx" denotes the error code
F / H / U
Cancelled automatically
5 seconds later.
To exit, press [POWER]
button on main unit or
remote control.
5 seconds later.
To exit, press [POWER]
button on main unit or
remote control.
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [0] button on
the remote control unit. *With
pointing of cursor up and
down on display.
press [STOP] button on the
main unit, and [0] button on
the remote control unit. *With
pointing of cursor up and
down on display.
Press [FL Display] on
remote control unit for next
page (FL Display) on values
of laser drive current.
remote control unit for next
page (FL Display) on values
of laser drive current.
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [PAUSE]
button on the remote
control unit.
press [STOP] button on the
main unit, and [PAUSE]
button on the remote
control unit.
Initial setting of laser drive current.
Initial current value for the DVD laser
and CD laser is separately saved in
the EEPROM IC.
Initial current value for the DVD laser
and CD laser is separately saved in
the EEPROM IC.
FL Display sequence:
Display 1 2.
Display 1 2.
The value denotes the current in decimal
notation.
notation.
The above example shows the initial current
is XXXmA and YYYmA for CD laser and
DVD laser respectively when the laser is
switched on.
is XXXmA and YYYmA for CD laser and
DVD laser respectively when the laser is
switched on.
(Display 1)
Laser current
measurement
mode
measurement
mode
(Display 2)
CD
Laser
Laser
DVD Laser
FL Display
Key Operation
Front Key
Item
Description
Mode Name
26
SA-PT560E / SA-PT560EB / SA-PT560EG
8.2.2. Service Mode Table 2
FL Display
Key Operation
Front Key
Item
Description
Mode Name
CD laser drive
current
measurement
Press [FL Display] on
remote control unit for next
page. (FL Display)
remote control unit for next
page. (FL Display)
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc) mode,
press [STOP] button on
the main unit, and [3]
button on the remote
control unit.
press [STOP] button on
the main unit, and [3]
button on the remote
control unit.
The value denotes the current in decimal
notation.
notation.
The above example shows the initial current is
XXXmA and the measured value is YYYmA.
XXXmA and the measured value is YYYmA.
DVD laser
drive current
measurement
CD laser current
measurement mode
measurement mode
(Display 1)
CD
laser initial
value
laser initial
value
CD laser
value
value
(Display 2)
Press [FL Display] on
remote control unit for next
page (FL Display) on values
of dvd drive current.
remote control unit for next
page (FL Display) on values
of dvd drive current.
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc) mode,
press [STOP] button on the
main unit, and
[FUNCTIONS] button on
the remote control unit.
press [STOP] button on the
main unit, and
[FUNCTIONS] button on
the remote control unit.
The value denotes the current in decimal
notation.
notation.
The above example shows the initial current
is XXXmA and the measured value is
YYYmA.
is XXXmA and the measured value is
YYYmA.
DVD laser current
measurement mode
measurement mode
(Display 1)
DVD
Laser
Initial Value
Laser
Initial Value
DVD
Laser
Value
Laser
Value
(Display 2)
DVD laser drive current measurement.
DVD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off.
DVD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off.
FL Display sequence:
Display 1 2.
Display 1 2.
CD laser drive current measurement.
CD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, CD laser
emission is kept on. It is turned off
when POWER key is switched off.
CD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, CD laser
emission is kept on. It is turned off
when POWER key is switched off.
FL Display sequence:
Display 1 2.
Display 1 2.
Region code display, TV broadcasting
system & the model no. information.
system & the model no. information.
Note: Refer to Figure 8.1 for "Video
Design Information".
Design Information".
Region display
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [6] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [6] button on the
remote control unit.
N: no PAL / P: PAL
Model
No.
Information
No.
Information
N: NTSC / 6: PAL60
Region No.: 0-8
CPPM/CRM
Keys Check
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [SOUND] button on
the remote control unit.
mode, press [STOP]
button on the main unit,
and [SOUND] button on
the remote control unit.
0: NG
1: OK
1: OK
0: NG
1: OK
1: OK
CPPM/CRM refers to the Content
Protection for Recordable Media and
Pre-Recorded Media. It displays the
existence of the keys as "1" or "0".
OK: Existing of keys.
NG: Non existing of keys.
Protection for Recordable Media and
Pre-Recorded Media. It displays the
existence of the keys as "1" or "0".
OK: Existing of keys.
NG: Non existing of keys.
27
SA-PT560E / SA-PT560EB / SA-PT560EG
English, Spanish,
Canadian, French
(S)
Japanese, English
English, French, German,
Spanish, Polish, Russian,
Czech, Hungarian
English, French, German,
Italian, Spanish, Polish,
Swedish, Dutch
English, French, German,
Spanish, Polish, Russian,
Czech, Hungarian
GCS, GD,
English, Traditional Chinese
GT, GCT
English, French, German,
Italian, Spanish, Polish,
Swedish, Dutch
English, Spanish, French,
Brazilian Portuguese
English, French, German,
Spanish, Polish, Russian,
Czech, Hungarian
GK
English, Simplified Chinese
GN
EE
PL, GCP, LB
E
P, PC, PX
GC, GS
EB, EG
NTSC (*B)
Source
Output
Screen Saver
NTSC
NTSC disc
NTSC (default)
PAL60
PAL disc
PAL
NTSC (*A)
Source
Output
Screen Saver
NTSC
NTSC disc
NTSC
PAL disc
PAL (DVD-V)
NTSC (DVD-A/VCD)
NTSC (*D)
Source
Output
Screen Saver
NTSC
NTSC disc
NTSC
PAL disc
NTSC
PAL (*C)
Source
Output
Screen Saver
PAL
NTSC disc
PAL60 (default)
NTSC
PAL disc
PAL
Explanation of Display
Individual Model Code
Can play PAL disc
Region code
N: If NTSC disc is played, NTSC output.
6: If NTSC disc is played, PAL60 output.
6: If NTSC disc is played, PAL60 output.
2
6
5
4
4
2
2
1
2
3
Region
Code
NTSC
PAL
NTSC
PAL
SECAM
NTSC
PAL
PAL
PAL
NTSC
PAL
TV Broadcasting
System
Signal System
NTSC (*A)
NTSC (*D)
NTSC (*B)
PAL (*C)
PAL (*C)
PAL (*C)
PAL (*C)
PAL (*C)
NTSC (*A)
NTSC (*B)
(Default)
2PN
4PN
6PN
5P6
3PN
4P6
2P6
2P6
1PN
2P6
Region Display
(Default)
Product
Model Series
Japan
South East Asia,
Korea, Taiwan
New Zealand,
Australia
Central/South/
Latin America
China
CIS
Europe
USA, Canada, PX
Europe
Middle East
Country Region
OSD Menu Language
OSD
Default
English
English
English
English
English
English
English
English
English
Japanese
Figure 8.1 Video Design Information
28
SA-PT560E / SA-PT560EB / SA-PT560EG
Click on the first or last page to see other SA-PT560E / SA-PT560EB / SA-PT560EG service manuals if exist.