Panasonic SA-PT160E / SA-PT160EB / SA-PT160EG Service Manual ▷ View online
8.2.3. Service Mode Table 3
FL Display
Key Operation
Front Key
Item
Description
Mode Name
Initialization
Cancelled automatically
5 seconds later.
5 seconds later.
Initialization.
User settings are cancelled and player
is initialized to factory setting.
It is necessary when after replacement
of Micro-processor (DV5 LSI) IC,
FLASH ROM IC (IC8651), EEPROM
IC (IC8611) & DVD Module P.C.B.
User settings are cancelled and player
is initialized to factory setting.
It is necessary when after replacement
of Micro-processor (DV5 LSI) IC,
FLASH ROM IC (IC8651), EEPROM
IC (IC8611) & DVD Module P.C.B.
Cancelled automatically
5 seconds later.
5 seconds later.
Region code display, TV broadcasting
system & the model no. information.
system & the model no. information.
Note: Refer to Figure 2 for "Video
Design Information".
Design Information".
Region display
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [6] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [6] button on the
remote control unit.
Region No.: 0-8
N: no PAL / P: PAL
N: NTSC / 6: PAL60
Model
No.
Information
No.
Information
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [ 10] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [ 10] button on the
remote control unit.
If the EEPROM version matches, checksum
[YYYY] is displayed.
[YYYY] is displayed.
If the version of the EEPROM does not match,
[NG] is displayed.
[NG] is displayed.
(a) If there is NO EEPROM header string
OR
(b) If there is no EEPROM (no data is received
by Micro-processor), [NO] is displayed.
OR
(b) If there is no EEPROM (no data is received
by Micro-processor), [NO] is displayed.
EEPROM
Checksum
(If applicable,
refer below.)
Checksum
(If applicable,
refer below.)
(Condition1)
Opecon
Version
Version
(Display 1)
(Display 2)
(Display 3)
(Condition 2)
(Condition 3)
Micro-processor
firmware version
display &
EEPROM
checksum
display.
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [7] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [7] button on the
remote control unit.
Press [FL Display] button on
remote control unit for next
page. (FL Display)
remote control unit for next
page. (FL Display)
Micro-processor firmware version
display & EEPROM checksum display.
EEPROM checksum is only available
due to existence of EEPROM IC.
display & EEPROM checksum display.
EEPROM checksum is only available
due to existence of EEPROM IC.
Note: Condition 1/2/3 shows the state
of EEPROM IC.
of EEPROM IC.
FL Display sequence:
Display 1 2 3.
Display 1 2 3.
25
SA-PT160E / SA-PT160EB / SA-PT160EG
TV Broadcasting
Signal System
Region Display
Code
System
(Default)
(Default)
English, Spanish, Canadian
French
(S)
Japan
2
NTSC
NTSC (*A)
2PN
Japanese, English
English, French, German,
Spanish, Polish, Russian,
Czech, Hungarian
English, French, German,
Italian, Spanish, Polish,
Swedish, Dutch
English, French, German,
Spanish, Polish, Russian,
Czech, Hungarian
GCS, GD,
South East Asia,
PAL
English, Traditional Chinese
GT, GCT
Korea, Taiwan
NTSC
New Zealand,
English, French, German,
Australia
Italian, Spanish, Polish,
Swedish, Dutch
Central/South/
NTSC (*D)
4PN
English, Spanish, French,
Latin America
Brazilian Portuguese
English, French, German,
Spanish, Polish, Russian,
Czech, Hungarian
GK
China
6
PAL
NTSC (*B)
6PN
English, Simplified Chinese
5P6
PAL (*C)
SECAM
5
NTSC
4
4
GN
EE
CIS
PL, GCP, LB
3PN
4P6
PAL (*C)
PAL
2P6
PAL (*C)
PAL
2
2P6
PAL (*C)
PAL
2
1PN
NTSC
1
E
Europe
2
PAL
PAL (*C)
2P6
P, PC, PX
USA, Canada, PX
NTSC (*A)
Europe
GC, GS
EB, EG
Middle East
3
NTSC (*B)
Product
OSD Menu Language
Model Series
Country Region
Region
Explanation of Display
Individual Model Code
can play PAL disc
Region code
N: If NTSC disc is played, NTSC output.
6: If NTSC disc is played, PAL60 output.
6: If NTSC disc is played, PAL60 output.
NTSC (*A)
NTSC (*B)
Source
Output
Source
Output
Screen Saver
NTSC
Screen Saver
NTSC
NTSC disc
NTSC
NTSC disc
NTSC (default)
PAL disc
PAL (DVD-V)
PAL60
NTSC (DVD-A/VCD)
PAL disc
PAL60
PAL (*C)
NTSC (*D)
Source
Output
Source
Output
Screen Saver
PAL
Screen Saver
NTSC
NTSC disc
PAL60 (default)
NTSC disc
NTSC
NTSC
PAL disc
NTSC
PAL disc
PAL
Figure 2
26
SA-PT160E / SA-PT160EB / SA-PT160EG
8.2.4. Service Mode Table 4
Cancelled automatically
5 seconds later.
5 seconds later.
CPPM/CRM
Keys Check
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [EQ] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [EQ] button on the
remote control unit.
0: NG
1: OK
1: OK
0: NG
1: OK
1: OK
DVD
Module P.C.B.
firmware
version display
Cancelled automatically
5 seconds later.
5 seconds later.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [8] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [8] button on the
remote control unit.
System controller
generation
generation
Destination
System
controller
version
controller
version
Region No.: 0-8
DVD Module P.C.B. firmware version
is displayed on the FL Display.
The firmware version can be updated
using recovery disc.
is displayed on the FL Display.
The firmware version can be updated
using recovery disc.
Note: It is necessary to check for
firmware version before carrying out
the version up using the disc.
firmware version before carrying out
the version up using the disc.
CPPM/CRM refers to the Content
Protection for Recordable Media and
Pre-Recorded Media. It displays the
existence of the keys as "1" or "0".
OK: Existing of keys.
NG: Non existing of keys.
Protection for Recordable Media and
Pre-Recorded Media. It displays the
existence of the keys as "1" or "0".
OK: Existing of keys.
NG: Non existing of keys.
FL Display
Key Operation
Front Key
Item
Description
Mode Name
DVD
Module P.C.B.
Reset
To reset DVD Module P.C.B.
This process is used when the DVD
Module P.C.B. or FLASH ROM
IC is replaced with a new one.
This process is used when the DVD
Module P.C.B. or FLASH ROM
IC is replaced with a new one.
Cancelled automatically
5 seconds later.
5 seconds later.
While in initialization
mode, press & hold
[STOP] button on the main
unit, follow by [ENTER]
button on the remote
control unit.
mode, press & hold
[STOP] button on the main
unit, follow by [ENTER]
button on the remote
control unit.
27
SA-PT160E / SA-PT160EB / SA-PT160EG
8.2.5. Service Mode Table 5
Timer 1 check
Cancelled automatically
5 seconds later.
5 seconds later.
DVD laser usage time
(Display 1)
(Display 2)
CD laser usage time
Cancelled automatically
5 seconds later
5 seconds later
Cancelled automatically
5 seconds later.
5 seconds later.
Cancelled automatically
5 seconds later.
5 seconds later.
Timer 1 reset
Timer 2 check
Timer 2 reset
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [ ] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [ ] button on the
remote control unit.
While displaying Timer 1
data, press [STOP] button
on the main unit, and [ ]
button on the remote
control unit.
data, press [STOP] button
on the main unit, and [ ]
button on the remote
control unit.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [ ] button on the
remote control unit.
mode, press [STOP]
button on the main unit,
and [ ] button on the
remote control unit.
While displaying Timer 2
data, press [STOP] button
on the main unit, and [ ]
button on the remote
control unit.
data, press [STOP] button
on the main unit, and [ ]
button on the remote
control unit.
Timer 1 check
Laser operation timer is measured
separately for DVD laser and CD laser.
Laser operation timer is measured
separately for DVD laser and CD laser.
FL Display sequence:
Display 1 2.
Display 1 2.
Press [FL Display] button for
next page of FL Display.
next page of FL Display.
Timer 1 reset
Laser operation timer of both DVD
laser and CD laser is reset all at once.
Laser operation timer of both DVD
laser and CD laser is reset all at once.
Timer 2 check
Spindle motor operation timer
Spindle motor operation timer
Timer 2 reset
Spindle motor operation timer
Spindle motor operation timer
Time is shown in 5 digits of decimal notation in
a unit of 1 hour.
"00000" will follow "99999".
a unit of 1 hour.
"00000" will follow "99999".
Shown to the above is DVD laser usage
time, and to the below is CD laser usage
time.
Time is shown in 4 digits of decimal notation
in a unit of 10 hours.
"0000" will follow "9999". (DVD laser)
time, and to the below is CD laser usage
time.
Time is shown in 4 digits of decimal notation
in a unit of 10 hours.
"0000" will follow "9999". (DVD laser)
Time is shown in 4 digits of decimal notation
in a unit of 10 hours.
"0000" will follow "9999". (CD laser)
in a unit of 10 hours.
"0000" will follow "9999". (CD laser)
Time is shown in 4 digits of decimal notation
in a unit of 10 hours.
It will clear to "0000" upon reset.
in a unit of 10 hours.
It will clear to "0000" upon reset.
Time is shown in 5 digits of decimal notation in
a unit of 1 hour.
It will be cleared to "00000" upon activating
this.
a unit of 1 hour.
It will be cleared to "00000" upon activating
this.
FL Display
Key Operation
Front Key
Item
Description
Mode Name
28
SA-PT160E / SA-PT160EB / SA-PT160EG
Click on the first or last page to see other SA-PT160E / SA-PT160EB / SA-PT160EG service manuals if exist.