Panasonic SA-PT160E / SA-PT160EB / SA-PT160EG Service Manual ▷ View online
7.6.2. File Extension Type Support (WMA/MP3/JPEG/*MPEG4/*DivX)
Tips
for making data discs
Tips for making data discs
When there are more than eight groups, the eighth group onwards will be displayed on one vertical line in the menu
screen.
There may be differences in the display order on the menu screen and computer screen.
This unit cannot play l
screen.
There may be differences in the display order on the menu screen and computer screen.
This unit cannot play l
fi es recorded using packet write.
DVD-RAM
Discs must conform to UDF 2.0.
DVD-R/RW
Discs must conform to UDF bridge (UDF 1.02/ISO9660).
This unit does not support multi-session. Only the default session is played.
This unit does not support multi-session. Only the default session is played.
CD-R/RW
Discs must conform to ISO9660 level 1 or 2 (except for extended formats).
This unit supports multi-session but if there are many sessions it takes more time for play to start. Keep the number of
sessions to a minimum to avoid this.
This unit supports multi-session but if there are many sessions it takes more time for play to start. Keep the number of
sessions to a minimum to avoid this.
Naming folders and files
Files are treated as contents and folders are treated as groups on this unit.
At the time of recording, prefi
At the time of recording, prefi
fi
x folder and le names. This should be with numbers that have
an equal number of digits, and should be done in the order you want to play them (this may
not work at times). Files must have the extension (
not work at times). Files must have the extension (
see below).
(Extension: ".WMA" or ".wma")
Compatible compression rate: between 48 kbps and 320 kbps.
You cannot play WMA files that are copy-protected.
This unit does not support Multiple Bit Rate (MBR).
You cannot play WMA files that are copy-protected.
This unit does not support Multiple Bit Rate (MBR).
(Extension: ".MP3" or ".mp3")
Compatible compression rate: between 32 kbps and 320 kbps.
This unit does not support ID3 tags.
Compatible sampling rates:
This unit does not support ID3 tags.
Compatible sampling rates:
DVD-RAM, DVD-R/RW: 11.02, 12, 22.05, 24, 44.1 and 48 kHz
CD-R/RW: 8, 11.02, 12, 16, 22.05, 24, 32, 44.1 and 48 kHz
(Extension: ".JPG", ".jpg", ".JPEG" or ".jpeg")
(Extension: ".ASF" or ".asf")
(Extension: ".DIVX", ".divx", ".AVI" or ".avi")
JPEG l
fi es taken on a digital camera that conform to DCF Standard (Design rule for Camera F ile system) Version 1.0 are
displayed. Files that have been altered, edited or saved with computer picture edi ting software may not be displayed.
You can play MPEG4 data [conforming to SD VIDEO speci c
fi ations (ASF standard)/MPEG4 (Simple Pro le) video
system/G.726 audio system] recorded with Panasonic SD multi cameras or DVD video rec orders with this unit.
The recording date may differ from that of the actual date.
The recording date may differ from that of the actual date.
This unit cannot display moving pictures, MOTION JPEG and other such formats, and still pictures other than JPEG
(Example: TIFF), or play pictures with attached audio.
(Example: TIFF), or play pictures with attached audio.
You can play all versions of DivX
fi
video (including DivX
fi
6) [DivX video system/MP3, Dolby Digital or MPEG audio
system] with standard playback of DivX
fi
media l
fi es. Functions added with DivX Ultra are not supported.
GMC (Global Motion Compensation) is not supported.
This unit supports all resolutions up to maximum of 720 x 480 (NTSC)/720 x 576 (PAL).
You can select up to eight types of audio and subtitles on this unit.
You can select up to eight types of audio and subtitles on this unit.
fi
DivX les greater than 2 GB or have no index may not be played properly on this unit.
fi
*
*
*
For E, EG areas only
21
SA-PT160E / SA-PT160EB / SA-PT160EG
8 Self-Diagnosis and Special Mode Setting
8.1. Service Mode Summary Table
The service modes can be activated by pressing various button combination on the main unit and remote control unit.
Below is the summary for the various modes for checking:
Player buttons
Remote control unit buttons
Application
Note
[STOP]
[0]
Error code check.
(Refer to the section
“8.2.1. Service Mode
Table 1” for more
information.)
“8.2.1. Service Mode
Table 1” for more
information.)
[5]
Jitter checking.
[PAUSE]
Initial setting of laser drive current.
[FUNCTIONS]
DVD laser drive current check.
(Refer to the section
“8.2.2. Service Mode
Table 2” for more
information.)
“8.2.2. Service Mode
Table 2” for more
information.)
[1]
ADSC internal RAM data check.
[3]
CD laser drive current check.
[6]
Region display and mode.
(Refer to the section
“8.2.3. Service Mode
Table 3“ for more
information.)
“8.2.3. Service Mode
Table 3“ for more
information.)
[7]
Micro-processor firmware version check.
[
]
Initialization of the player (factory setting is restored).
Used after replacement of Micro-processor (DV5 LSI) IC, FLASH
ROM IC (IC8651), EEPROM IC (IC8611) and DVD Module
P.C.B.
Used after replacement of Micro-processor (DV5 LSI) IC, FLASH
ROM IC (IC8651), EEPROM IC (IC8611) and DVD Module
P.C.B.
[8]
DVD Module P.C.B. firmware version check.
(Refer to the section
“8.2.4. Service Mode
Table 4“ for more
information.)
“8.2.4. Service Mode
Table 4“ for more
information.)
[EQ]
CPPM/CRM keys check.
[ENTER]
DVD Module P.C.B. reset.
[
]
Timer 1 check.
(Refer to the section
“8.2.5. Service Mode
Table 5“ for more
information.)
“8.2.5. Service Mode
Table 5“ for more
information.)
[
]
Timer 1 reset.
[
]
Timer 2 check.
[
]
Timer 2 reset.
Note:
An error code will be canceled if a power supply is turned OFF.
*1: CPPM is the copy guard function beforehand written in the disk for protection of copyrights.
*2: CEC is the consumer electronic control used for high-level user control of HDMI-connected devices.
*3: HDCP is the specification developed to control digital audio & video contents transmission for DVI or HDMI connections.
8.2. Service Mode Table
By pressing various button combinations on the main unit and remote control unit, you can activate the various service modes for
checking.
checking.
Special Note:
•
•
•
•
Due to the limitations of the no. characters that can be shown on the FL Display, the “FL Display” button on the remote
control unit can be used to show the two display pages. (Display 1 / Display 2).
control unit can be used to show the two display pages. (Display 1 / Display 2).
•
•
•
•
Refer to Section 7.1 for the section on “Remote Control Key Buttons Operations”.
22
SA-PT160E / SA-PT160EB / SA-PT160EG
8.2.1. Service Mode Table 1
FL Display
Key Operation
Front Key
Item
Jitter check
Description
Mode Name
Initial setting
of laser drive
current
Error code
check
Cancelled automatically
5 seconds later.
To exit, press [POWER]
button on main unit or
remote control.
5 seconds later.
To exit, press [POWER]
button on main unit or
remote control.
Press [FL Display] on
remote control unit for next
page (FL Display) on values
of laser drive current.
remote control unit for next
page (FL Display) on values
of laser drive current.
Cancelled automatically
5 seconds later.
5 seconds later.
Press [POWER] button to
exit.
exit.
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [5] button on
the remote control unit.
press [STOP] button on the
main unit, and [5] button on
the remote control unit.
Jitter check.
Jitter rate is measured and displayed.
Measurement is repeatedly done in
the cycle of one second. Read error
counter starts from zero upon mode
setting.
When target block data failed to be
read out, the counter advances by one
increment. When the failure is caused
by minor error, it may be corrected
when retried to enable successful
reading.
In this case, the counter advances by
one. When the error persists even
after retry, the counter may jump by
two or more.
Jitter rate is measured and displayed.
Measurement is repeatedly done in
the cycle of one second. Read error
counter starts from zero upon mode
setting.
When target block data failed to be
read out, the counter advances by one
increment. When the failure is caused
by minor error, it may be corrected
when retried to enable successful
reading.
In this case, the counter advances by
one. When the error persists even
after retry, the counter may jump by
two or more.
FL Display sequence:
Display 1 2.
Display 1 2.
Jitter rate is shown in decimal notation to
one place of decimal.
Focus drive value is shown in hexadecimal
notation.
one place of decimal.
Focus drive value is shown in hexadecimal
notation.
(Display 1)
(Display 1)
(Display 2)
(Display 2)
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [0] button on
the remote control unit. * With
pointing of cursor up and
down on display.
press [STOP] button on the
main unit, and [0] button on
the remote control unit. * With
pointing of cursor up and
down on display.
Error code check
The latest error code stored in the
EEPROM IC is displayed.
The latest error code stored in the
EEPROM IC is displayed.
Note: Refer to "Section 8.3 DVD Self
Diagnostic Function-Error Code" for
more detailed information on the error
codes.
Diagnostic Function-Error Code" for
more detailed information on the error
codes.
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [PAUSE]
button on the remote
control unit.
press [STOP] button on the
main unit, and [PAUSE]
button on the remote
control unit.
Initial setting of laser drive current.
Initial current value for the DVD laser
and CD laser is separately saved in
the EEPROM IC.
Initial current value for the DVD laser
and CD laser is separately saved in
the EEPROM IC.
FL Display sequence:
Display 1 2.
Display 1 2.
Press [FL Display] on
remote control unit for next
page (FL Display).
remote control unit for next
page (FL Display).
Jitter rate
Lead
Error
Counter
Error
Counter
Focus Drive
Value
Value
Jitter check
mode
mode
U / H / F
Laser current
measurement
mode
measurement
mode
CD
Laser
Laser
DVD Laser
Error code (play_err) is expressed in the
following convention.
Error code = 0 x DAXX is expressed:
following convention.
Error code = 0 x DAXX is expressed:
DVDnn U12
Error code = 0 x DBXX is expressed:
DVDnn H12
Error code = 0 x DXXX is expressed:
DVDnn F123
Error code = 0 x 0000 is expressed:
DVDnn F---
* "xx" denotes the error code
The value denotes the current in decimal
notation.
notation.
The above example shows the initial
current is XXXmA and YYYmA for CD
laser and DVD laser respectively when
the laser is switched on.
current is XXXmA and YYYmA for CD
laser and DVD laser respectively when
the laser is switched on.
23
SA-PT160E / SA-PT160EB / SA-PT160EG
8.2.2. Service Mode Table 2
FL Display
Key Operation
Front Key
Item
Description
Mode Name
Press [FL Display] on
remote control unit for next
page. (FL Display)
remote control unit for next
page. (FL Display)
Cancelled automatically
5 seconds later.
5 seconds later.
CD laser drive
current
measurement
In STOP (no disc) mode,
press [STOP] button on
the main unit, and [3]
button on the remote
control unit.
press [STOP] button on
the main unit, and [3]
button on the remote
control unit.
CD laser drive current measurement.
CD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, CD laser
emission is kept on. It is turned off
when POWER key is switched off.
CD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, CD laser
emission is kept on. It is turned off
when POWER key is switched off.
FL Display sequence:
Display 1 2.
Display 1 2.
CD laser current
measurement mode
measurement mode
CD
laser initial
value
laser initial
value
CD laser
value
value
The value denotes the current in decimal
notation.
notation.
The above example shows the initial current
is 0XXmA and the measured value is 0YYmA.
is 0XXmA and the measured value is 0YYmA.
To exit, press [POWER]
button.
button.
ADSC internal
RAM data
check
In STOP (no disc) mode,
press [STOP] button on
the main unit, and [1]
button on the remote
press [STOP] button on
the main unit, and [1]
button on the remote
ADSC internal RAM data check.
ADSC internal RAM data is read out
and displayed.
ADSC internal RAM data is read out
and displayed.
The value is shown in hexadecimal
notation. The above example shows the
data in ADSC address FBOh is XXXXh.
notation. The above example shows the
data in ADSC address FBOh is XXXXh.
Address
RAM data
for specified
address
for specified
address
DVD laser
drive current
measurement
Press [FL Display] on
remote control unit for next
page (FL Display) on values
of dvd drive current.
remote control unit for next
page (FL Display) on values
of dvd drive current.
Cancelled automatically
5 seconds later.
5 seconds later.
(Display 1)
(Display 2)
(Display 1)
(Display 2)
In STOP (no disc) mode,
press [STOP] button on the
main unit, and
[FUNCTIONS] button on
the remote control unit.
press [STOP] button on the
main unit, and
[FUNCTIONS] button on
the remote control unit.
DVD laser drive current measurement.
DVD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off.
DVD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off.
FL Display sequence:
Display 1 2.
Display 1 2.
DVD laser current
measurement mode
measurement mode
DVD
Laser
Initial Value
Laser
Initial Value
DVD
Laser
Value
Laser
Value
The value denotes the current in decimal
notation.
notation.
The above example shows the initial
current is XXXmA and the measured
value is YYYmA.
current is XXXmA and the measured
value is YYYmA.
24
SA-PT160E / SA-PT160EB / SA-PT160EG
Click on the first or last page to see other SA-PT160E / SA-PT160EB / SA-PT160EG service manuals if exist.