Panasonic SA-NC6EB Service Manual ▷ View online
Step 1 Slide the clamp plate unit while pressing the stopper in
the arrow direction, and remove the clamp plate unit.
the arrow direction, and remove the clamp plate unit.
Step 2 Raise the CD Loading unit vertically.
Step 3 Slide the lever fully in the direction of arrow, pull the tray
out. (The sub tray and tray be out together).
Note:
Tray cannot be take out when CD Loading unit place in horizon
even pushing lever.
Step 3 Slide the lever fully in the direction of arrow, pull the tray
out. (The sub tray and tray be out together).
Note:
Tray cannot be take out when CD Loading unit place in horizon
even pushing lever.
Step 4 Remove the traverse unit.
Step 4 Spread the tabs at the both side. (The tray slides a little
forward and stops.)
Step 5 Hook the drive arm hanging area over the tray slider
and tray.
Step 6 Pull out tray and sub tray.
forward and stops.)
Step 5 Hook the drive arm hanging area over the tray slider
and tray.
Step 6 Pull out tray and sub tray.
10.15.3. Disassembly of Tray and Sub Tray
61
SA-NC6EB
Step 7 Release the vertically lock lever, free the sensor lever.
Step 8 Pull the sub tray.
· Assembly of the tray unit
Step 1 Insert a part of the tray and sub tray into the unit sliding
over the groove on the mecha chassis.
· Assembly of the tray unit
Step 1 Insert a part of the tray and sub tray into the unit sliding
over the groove on the mecha chassis.
Step 1 Spread the tabs at the both sides and push out the drive
arm.
arm.
Step 2 Insert the tray to the point before the tab of the mecha
chassis.
Step 3 Hook the drive arm hanging area over the tray slider
and tray.
chassis.
Step 3 Hook the drive arm hanging area over the tray slider
and tray.
Step 4 Push the tray.
Step 5 Make sure that the tray and the drive arm move
smoothly.
Step 5 Make sure that the tray and the drive arm move
smoothly.
10.15.4. Disassembly of Loading Section
62
SA-NC6EB
Step 3 Release the 2 tabs and remove the guide piece (L).
Step 4 Release the 2 tabs and remove the guide piece (R).
Step 5 Remove horizon lock lever spring hooking area.
Step 6 Remove the tab and remove the horizon lock lever.
Step 4 Release the 2 tabs and remove the guide piece (R).
Step 5 Remove horizon lock lever spring hooking area.
Step 6 Remove the tab and remove the horizon lock lever.
Step 7 Hook the lock lever spring on the lock lever projection
part temporary.
Step 8 Unlock the tab and remove the lock lever.
Step 9 Remove the belt.
part temporary.
Step 8 Unlock the tab and remove the lock lever.
Step 9 Remove the belt.
Step 10 Release 2 tab and remove pulley gear.
Step 11 Remove the relay gear.
Step 11 Remove the relay gear.
63
SA-NC6EB
Step 12 Turn the change lever in the arrow direction till it stops.
Step 13 Hook the change lever spring on the change lever
project part temporary.
Step 13 Hook the change lever spring on the change lever
project part temporary.
Step 14 Remove the change lever.
Step 1 Remove 3 screws.
Step 2 Remove Tray Loading P.C.B.
Step 2 Remove Tray Loading P.C.B.
Step 1 Lift up the lever upward, open the cassette deck.
Step 15 Remove the drive rack, the sub rack and drive gear.
Step 17 Remove Tray Loading P.C.B..
Step 18 Desolder 2 pins, remove the motor.
Step 18 Desolder 2 pins, remove the motor.
10.15.5. Disassembly of Tray Loading P.C.B
10.16. Disassembly of cassette lid
· Follow the (Step 1) - (Step 5) of Item 10.4
· Follow the (Step 1) - (Step 3) of Item 10.6
· Follow the (Step 1) - (Step 5) of Item 10.8
· Follow the (Step 1) - (Step 3) of Item 10.12
· Follow the (Step 1) - (Step 3) of Item 10.6
· Follow the (Step 1) - (Step 5) of Item 10.8
· Follow the (Step 1) - (Step 3) of Item 10.12
64
SA-NC6EB
Click on the first or last page to see other SA-NC6EB service manuals if exist.