Panasonic SA-HT543EE Service Manual ▷ View online
7.4.2. File Extension Type Support (WMA/MP3/JPEG/MPEG4/DivX)
17
SA-HT543EE
7.5. About DivX VOD Content
18
SA-HT543EE
8 Self-Diagnosis and special mode setting
8.1. Service Mode Summary Table
The service modes can be activated by pressing various button combination on the player and remote control unit.
Below is the summary of major checking:
Below is the summary of major checking:
Player buttons
Remote control unit buttons
Application
Note
STOP
0
Error code check
(Refer to the section
“8.2.1. Service Mode
Table 1” for more
information).
“8.2.1. Service Mode
Table 1” for more
information).
1
ADSC internal RAM data check
5
Jitter checking
FUNCTIONS
DVD laser drive current check
PAUSE
Initial setting of laser drive current.
3
CD laser drive current check
(Refer to the section
“8.2.2. Service Mode
Table 2” for more
information).
“8.2.2. Service Mode
Table 2” for more
information).
6
Region display and mode
7
Micro-processor firmware version check
8
HDMI module firmware version check.
Initialization of the player (factory setting is restored.)
Used after replacement of micro-computer, FLASH ROM IC,
EEPROM and HDMI module.
Initialization of the player (factory setting is restored.)
Used after replacement of micro-computer, FLASH ROM IC,
EEPROM and HDMI module.
MENU
Communication error display
ENTER
DVD Module reset
(Refer to the section
“8.2.3. Service Mode
Table 3“ for more
information).
“8.2.3. Service Mode
Table 3“ for more
information).
Timer 1 check
Timer 1 reset
Timer 2 check
Timer 2 reset
PAUSE
Writing of laser drive current value after replacement of optical
pickup (Do use this function only when optical pickup is
replaced.)
pickup (Do use this function only when optical pickup is
replaced.)
(Refer to the section
“8.2.4. Optical Pick-up
Self-Diagnosis” for more
information).
“8.2.4. Optical Pick-up
Self-Diagnosis” for more
information).
8.2. Service Mode Table
By pressing various button combinations on the player and remote control unit can activate the various service modes for checking.
Special Note:
Special Note:
Due to the limitations of the no. characters that can be shown on FL Display, the “FL Display” button on the remote control uni
is used to show the following page. (Display 1/Display 2).
is used to show the following page. (Display 1/Display 2).
19
SA-HT543EE
8.2.1. Service Mode Table 1
FL Display
Key Operation
Front Key
Item
Jitter check mode
To exit, Press STOP or
PLAY button.
PLAY button.
Jitter check
Description
Mode Name
Initial setting
of laser drive
current
DVD laser
drive current
measurement
ADSC internal
RAM data
check
Error code
check
Cancelled automatically
5 seconds later.
To exit, press [POWER]
button on main unit or
remote control.
5 seconds later.
To exit, press [POWER]
button on main unit or
remote control.
Press "FL Display" on
remote control unit for next
page (FL Display) on values
of laser drive current.
remote control unit for next
page (FL Display) on values
of laser drive current.
Press "FL Display" on
remote control unit for next
page (FL Display) on values
of dvd drive current.
remote control unit for next
page (FL Display) on values
of dvd drive current.
Cancelled automatically
5 seconds later.
5 seconds later.
Cancelled automatically
5 seconds later.
5 seconds later.
RAM data for
specified address
specified address
Address
Press STOP or OPEN
button to exit.
button to exit.
In STOP (no disc) mode,
press STOP button on the
player, and "5" button on
the remote control unit.
press STOP button on the
player, and "5" button on
the remote control unit.
Jitter check
Jitter rate is measured and displayed.
Measurement is repeatedly done in
the cycle of one second. Read error
counter starts from zero upon mode
setting. When target block data failed
to be read out, the counter advances
by one increment. When the failure is
caused by minor error, it may be
corrected when retried to enable
successful reading. In this case, the
counter advances by one. When the
error persists even after retry, the
counter may jump by two or more.
Jitter rate is measured and displayed.
Measurement is repeatedly done in
the cycle of one second. Read error
counter starts from zero upon mode
setting. When target block data failed
to be read out, the counter advances
by one increment. When the failure is
caused by minor error, it may be
corrected when retried to enable
successful reading. In this case, the
counter advances by one. When the
error persists even after retry, the
counter may jump by two or more.
Jitter rate is shown in decimal notation to
one place of decimal.
Focus drive value is shown in hexadecimal
notation.
one place of decimal.
Focus drive value is shown in hexadecimal
notation.
In STOP (no disc) mode,
press STOP button on the
player, and "0" button on the
remote control unit. * With
pointing of cursor up and
down on display.
press STOP button on the
player, and "0" button on the
remote control unit. * With
pointing of cursor up and
down on display.
Error code check
The latest error code stored in the
EEPROM IC is displayed.
The latest error code stored in the
EEPROM IC is displayed.
Error code (play_err) is expressed in the
following convention.
Error code = 0 x DAXX is expressed:
following convention.
Error code = 0 x DAXX is expressed:
DVDnn UXX
Error code = 0 x DBXX is expressed:
DVDnn HXX
Error code = 0 x DXXX is expressed:
DVDnn FXXX
Error code = 0 x 0000 is expressed:
DVDnn F---
* "xx" denotes the error code
In STOP (no disc) mode,
press STOP button on the
player, and PAUSE button
on the remote control unit.
press STOP button on the
player, and PAUSE button
on the remote control unit.
Initial setting of laser drive current.
Initial current value for each of DVD
laser and CD laser is separately saved
in the EEPROM IC.
Initial current value for each of DVD
laser and CD laser is separately saved
in the EEPROM IC.
The value denotes the current in decimal
notation. The below example shows the
initial current is 24mA and 19mA for DVD
laser and CD laser respectively when the
laser is switched on.
notation. The below example shows the
initial current is 24mA and 19mA for DVD
laser and CD laser respectively when the
laser is switched on.
In STOP (no disc) mode,
press STOP button on the
player, and FUNCTIONS
button on the remote
control unit.
press STOP button on the
player, and FUNCTIONS
button on the remote
control unit.
DVD laser drive current measurement
·DVD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off. (It
is also turned off when POWER button
on the player is switched off.)
·DVD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off. (It
is also turned off when POWER button
on the player is switched off.)
In STOP (no disc) mode,
press STOP button on the
player, and "1" button on
the remote control unit.
press STOP button on the
player, and "1" button on
the remote control unit.
ADSC internal RAM data check
·ADSC internal RAM data is read out
and displayed.
·ADSC internal RAM data is read out
and displayed.
Laser current
measurement mode
measurement mode
DVD laser current
measurement mode
measurement mode
The value denotes the current in decimal
notation.
The below example shows the initial current
is 19mA and the measured value is 19mA.
notation.
The below example shows the initial current
is 19mA and the measured value is 19mA.
The value is shown in hexadecimal
notation. The above example shows the
data in ADSC address OFAh is 6901h.
notation. The above example shows the
data in ADSC address OFAh is 6901h.
Jitter rate
Press "FL Display" on
remote control unit for next
page (FL Display).
remote control unit for next
page (FL Display).
20
SA-HT543EE
Click on the first or last page to see other SA-HT543EE service manuals if exist.