Panasonic SA-AK330EE (serv.man4) Service Manual ▷ View online
* The mechanism as shown below is for DECK1. For DECK
2, perform the same procedures.
2, perform the same procedures.
Step 1 Release the 2 claws, and then remove the pinch roller
(R), (F).
Step 2 Release the 2 claws, and then remove the head
connector.
(R), (F).
Step 2 Release the 2 claws, and then remove the head
connector.
Step 3 Remove 2 screws.
9.13. Replacement for the pinch roller ass’y and head block
· Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet
· Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid
· Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit
· Follow the (Step 1) - (Step 3) of Item 9.10 - Disassembly of Front Panel Unit
· Follow the (Step 1) - (Step 5) of Item 9.11 - Disassembly of Deck Mechanism Unit
· Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid
· Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit
· Follow the (Step 1) - (Step 3) of Item 9.10 - Disassembly of Front Panel Unit
· Follow the (Step 1) - (Step 5) of Item 9.11 - Disassembly of Deck Mechanism Unit
33
SA-AK330EE
Step 1 Release the 2 claws, and then remove the head
connector.
Step 2 De-solder plunger point.
Step 3 Remove the Deck Mechanism P.C.B.
connector.
Step 2 De-solder plunger point.
Step 3 Remove the Deck Mechanism P.C.B.
Step 4 Remove 3 screws.
Step 5 Remove the flywheel R.
Step 6 Release the claw of tape side, and then remove the
winding lever and spring.
Step 7 Remove the flywheel F.
[Installation of the belt]
Step 1 The boss and marking should be positioned
horizontally.
Step 6 Release the claw of tape side, and then remove the
winding lever and spring.
Step 7 Remove the flywheel F.
[Installation of the belt]
Step 1 The boss and marking should be positioned
horizontally.
9.14. Replacement for the Deck motor ass’y, capstan belt A, capstan belt B
and winding belt
· Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet
· Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid
· Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit
· Follow the (Step 1) - (Step 3) of Item 9.10 - Disassembly of Front Panel Unit
· Follow the (Step 1) - (Step 5) of Item 9.11 - Disassembly of Deck Mechanism Unit
· Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid
· Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit
· Follow the (Step 1) - (Step 3) of Item 9.10 - Disassembly of Front Panel Unit
· Follow the (Step 1) - (Step 5) of Item 9.11 - Disassembly of Deck Mechanism Unit
34
SA-AK330EE
Step 2 Put the winding belt on the pulley temporarily.
Step 3 Install the flywheel F.
Step 4 Put the winding belt on the flywheel F.
Step 5 Install the winding lever and spring while pressing the
winding arm in the direction of arrow.
Step 3 Install the flywheel F.
Step 4 Put the winding belt on the flywheel F.
Step 5 Install the winding lever and spring while pressing the
winding arm in the direction of arrow.
Step 6 Install the flywheel R.
Step 7 Put the capstan belt A temporarily as shown below.
Step 8 Put the capstan belt B on the motor ass’y pulley.
Step 9 Install the sub chassis to the mechanism, and then
tighten screws.
Step 9 Install the sub chassis to the mechanism, and then
tighten screws.
35
SA-AK330EE
Step 10 Remove 3 screws.
Step 11 Put the capstan belt B as shown below.
Step 11 Put the capstan belt B as shown below.
Step 12 Put the capstan belt A on the motor ass’y pulley.
36
SA-AK330EE
Click on the first or last page to see other SA-AK330EE (serv.man4) service manuals if exist.