Panasonic RF-800UGA / RF-800UGS Service Manual ▷ View online
17
6.9.
Disassembly of Tuner P.C.B.
• Refer to “Disassembly of Rear Cabinet Block”.
• Refer to “Disassembly of Front Cabinet Block”.
• Refer to “Disassembly of Front Cabinet Block”.
Preparation before assembling:
Turn the Dial Pointer to the end position.
Turn the Dial Pointer to the end position.
Step 1 : Desolder the 2P Wire (Speaker-Tuner) at the terminals
on the Speaker Unit.
Caution : During assembling, ensure the speaker wire is
solder at the correct polarity.
on the Speaker Unit.
Caution : During assembling, ensure the speaker wire is
solder at the correct polarity.
Step 2 : Remove the Volume Knob.
Caution : Keep the Volume Knob in safe place and place it
back during assembling.
Caution : Keep the Volume Knob in safe place and place it
back during assembling.
Step 3 : Remove 4 screws.
18
Step 4 : Detach 2P cable at the connector (CN104) on the
Tuner P.C.B..
Step 5 : Detach 2P cable at the connector (CN105) on the
Tuner P.C.B..
Step 6 : Detach 6P cable at the connector (CN101) on the
Tuner P.C.B..
Tuner P.C.B..
Step 5 : Detach 2P cable at the connector (CN105) on the
Tuner P.C.B..
Step 6 : Detach 6P cable at the connector (CN101) on the
Tuner P.C.B..
Caution : During assembling, dressed the 2P wires as
shown.
shown.
Step 7 : Remove the Tuner P.C.B..
Caution : During assembling, align the Tuner P.C.B. with
the guides & inserted into the Front Cabinet Block.
the guides & inserted into the Front Cabinet Block.
19
Caution : Ensure that the Tuner P.C.B. is fully seated on to
the guide as shown.
the guide as shown.
6.10. Disassembly of USB P.C.B.
• Refer to “Disassembly of Rear Cabinet Block”.
• Refer to “Disassembly of Front Cabinet Block”.
• Refer to “Disassembly of Tuner P.C.B.”.
• Refer to “Disassembly of Front Cabinet Block”.
• Refer to “Disassembly of Tuner P.C.B.”.
Step 1 : Remove the Band Spring.
Caution : Keep the Band Spring in safe place and place it
back during assembling.
Caution : Keep the Band Spring in safe place and place it
back during assembling.
Step 2 : Remove the Band/Vol Knob.
Caution : Keep the Band/Vol Knob in safe place and place
them back during assembling.
Caution : Keep the Band/Vol Knob in safe place and place
them back during assembling.
20
Step 3 : Turn the Band Rotary Lever clockwise towards to the
guide as shown.
guide as shown.
Step 4 : Lift up to remove the Band Rotary Lever.
Caution : During assembling, align the guide of the Band
Rotary Lever with the rib of the Front Cabinet Block .
Caution : During assembling, align the guide of the Band
Rotary Lever with the rib of the Front Cabinet Block .
Step 5 : Remove 5 screws.
Step 6 : Remove the USB P.C.B..
Caution : During assembling, ensure that the USB P.C.B. is
properly seated onto the locators.
properly seated onto the locators.
Click on the first or last page to see other RF-800UGA / RF-800UGS service manuals if exist.