Panasonic RF-800UGA / RF-800UGS Service Manual ▷ View online
13
6.4.
Disassembly of Rear Cabinet
Block
Block
Step 1 : Press the OPEN button to open the Battery Cover
Assembly.
Assembly.
Step 2 : Remove 5 screws.
Step 3 : Slightly lift up the Rear Cabinet Block.
Step 4 : Detach 2P cable at the connector (CN1) on the Tuner
P.C.B..
Step 4 : Detach 2P cable at the connector (CN1) on the Tuner
P.C.B..
Step 5 : Detach 6P cable at the connector (CN2) on the Tuner
P.C.B..
Step 6 : Lift up to remove the Rear Cabinet Block.
P.C.B..
Step 6 : Lift up to remove the Rear Cabinet Block.
14
6.5.
Disassembly of Battery P.C.B.
• Refer to “Disassembly of Rear Cabinet Block”.
Step 1 : Release the catch.
Step 2 : Release the 2P Cable from the slot.
Caution : During assembling, ensure that the 2P cable is
properly inserted into the slot.
Step 3 : Slightly press the Battery P.C.B. by using screwdriver.
Caution : During assembling, ensure that the 2P cable is
properly inserted into the slot.
Step 3 : Slightly press the Battery P.C.B. by using screwdriver.
Step 4 : Remove the Battery P.C.B..
Caution : During assembling, inserted the 2P Cable into
the opening of Rear Cabinet Block as diagram shown.
Ensure the Battery P.C.B. is seated properly into the slots.
Caution : During assembling, inserted the 2P Cable into
the opening of Rear Cabinet Block as diagram shown.
Ensure the Battery P.C.B. is seated properly into the slots.
15
6.6.
Disassembly of Jack P.C.B.
• Refer to “Disassembly of Rear Cabinet Block”.
Step 1 : Release the 6P Cable from the slots.
Caution : During assembling, ensure that the 6P cable is
properly inserted into the slots.
Caution : During assembling, ensure that the 6P cable is
properly inserted into the slots.
Step 2 : Remove 1 screw.
Step 3 : Remove the Support P.C.B..
Caution 1 : Keep the Support P.C.B. in safe place and place
it back during assembling.
Caution 1 : Keep the Support P.C.B. in safe place and place
it back during assembling.
Step 4 : Remove the Jack P.C.B..
Caution : During assembling, ensure that the Jack P.C.B.
is fully inserted into the guides.
Caution : During assembling, ensure that the Jack P.C.B.
is fully inserted into the guides.
16
6.7.
Disassembly of Front Cabinet
Block
Block
• Refer to “Disassembly of Rear Cabinet Block”.
Step 1 : Remove 2 screws.
Step 2 : Remove the Front Cabinet Block.
6.8.
Disassembly of Speaker Unit
• Refer to “Disassembly of Rear Cabinet Block”.
• Refer to “Disassembly of Front Cabinet Block”.
• Refer to “Disassembly of Front Cabinet Block”.
Step 1 : Remove 4 screws.
Step 2 : Desolder the 2P Wire (Speaker-Tuner) at the terminals
on the Speaker Unit.
Caution : During assembling, ensure the speaker wire is
solder at the correct polarity.
Step 2 : Desolder the 2P Wire (Speaker-Tuner) at the terminals
on the Speaker Unit.
Caution : During assembling, ensure the speaker wire is
solder at the correct polarity.
Step 3 : Remove the Speaker Unit.
Click on the first or last page to see other RF-800UGA / RF-800UGS service manuals if exist.