Panasonic CS-E7JKEW / CU-E7JKE / CS-E9JKEW / CU-E9JKE / CS-E12JKEW / CU-E12JKE / CS-E15JKEW / CU-E15JKE / CU-E15JKE-1 / CS-E7JKEW-3 / CU-E7JKE-3 / CS-E9JKEW-3 / CU-E9JKE-3 / CS-E12JKEW-3 / CU-E12JKE-3 / CS-XE7JKEW / CS-XE9JKEW / CS-XE12JKEW / CS-XE15JKEW Service Manual ▷ View online
101
16.4.20. H99 (Indoor Freeze Prevention Protection: Cooling or Soft Dry)
Error code will not display (no TIMER LED blinking) but store in EEPROM
Malfunction Decision Conditions
Freeze prevention control takes place (when indoor pipe temperature is lower than 2
°C)
Malfunction Caused
• Clogged air filter of the indoor unit
• Dust accumulation on the indoor unit heat exchanger
• Air short circuit
• Detection error due to faulty indoor pipe temperature sensor
• Detection error due to faulty indoor unit PCB
• Dust accumulation on the indoor unit heat exchanger
• Air short circuit
• Detection error due to faulty indoor pipe temperature sensor
• Detection error due to faulty indoor unit PCB
Troubleshooting
102
16.4.21. F11 (4-way valve Abnormality)
Malfunction Decision Conditions
• When heating operation, when indoor pipe temperature is below 10
°C
• When cooling operation, when indoor pipe temperature is above 45
°C
Malfunction Caused
• Connector in poor contact
• Faulty sensor
• Faulty outdoor unit PCB
• 4-way valve defective
• Faulty sensor
• Faulty outdoor unit PCB
• 4-way valve defective
Troubleshooting
103
16.4.22. F17 (Indoor Standby Units Freezing Abnormality)
Malfunction Decision Conditions
• When the different between indoor intake air temperature and indoor pipe temperature is above 10
°C or indoor pipe temperature
is below -1.0
°C
Remark:
When the indoor standby unit is freezing, the outdoor unit transfers F17 error code to the corresponding indoor unit and H39 to
other indoor unit(s).
When the indoor standby unit is freezing, the outdoor unit transfers F17 error code to the corresponding indoor unit and H39 to
other indoor unit(s).
Malfunction Caused
• Wrong wiring connection
• Faulty sensor
• Faulty expansion valve
• Faulty sensor
• Faulty expansion valve
Troubleshooting
104
16.4.23. F90 (Power Factor Correction Protection)
Malfunction Decision Conditions
During startup and operation of cooling and heating, when Power Factor Correction (PFC) protection circuitry at the outdoor unit
main PCB senses abnormal high DC voltage level.
main PCB senses abnormal high DC voltage level.
Malfunction Caused
• DC voltage peak due to power supply surge.
• DC voltage peak due to compressor windings not uniform.
• Faulty outdoor PCB.
• DC voltage peak due to compressor windings not uniform.
• Faulty outdoor PCB.
Troubleshooting
Click on the first or last page to see other CS-E7JKEW / CU-E7JKE / CS-E9JKEW / CU-E9JKE / CS-E12JKEW / CU-E12JKE / CS-E15JKEW / CU-E15JKE / CU-E15JKE-1 / CS-E7JKEW-3 / CU-E7JKE-3 / CS-E9JKEW-3 / CU-E9JKE-3 / CS-E12JKEW-3 / CU-E12JKE-3 / CS-XE7JKEW / CS-XE9JKEW / CS-XE12JKEW / CS-XE15JKEW service manuals if exist.