Panasonic CS-E10JD3EA / U-E10HBEA / CS-E15JD3EA / CU-E15HBEA / CS-E18JD3EA / CU-E18HBEA Service Manual ▷ View online
77
15.5.18. F93 (Compressor Rotation Failure)
Malfunction Decision Conditions
A compressor rotation failure is detected by checking the compressor running condition through the position detection circuit.
A compressor rotation failure is detected by checking the compressor running condition through the position detection circuit.
Malfunction Caused
• Compressor terminal disconnect.
• Outdoor PCB malfunction.
• Compressor malfunction.
• Outdoor PCB malfunction.
• Compressor malfunction.
Troubleshooting
78
15.5.19. F95 (Cooling High Pressure Abnormality)
Malfunction Decision Conditions
During operation of cooling, when outdoor unit heat exchanger high temperature data (61
During operation of cooling, when outdoor unit heat exchanger high temperature data (61
°C) is detected by the outdoor pipe
temperature sensor.
Malfunction Caused
• Air short circuit at outdoor unit.
• Dust accumulation on the outdoor unit heat exchanger.
• 2/3 way valve closed.
• Faulty outdoor unit fan motor.
• Excessive refrigerant.
• Clogged expansion valve or strainer.
• Faulty outdoor pipe temperature sensor.
• Faulty outdoor unit PCB.
• Dust accumulation on the outdoor unit heat exchanger.
• 2/3 way valve closed.
• Faulty outdoor unit fan motor.
• Excessive refrigerant.
• Clogged expansion valve or strainer.
• Faulty outdoor pipe temperature sensor.
• Faulty outdoor unit PCB.
Troubleshooting
79
15.5.20. F96 (IPM Overheating)
Malfunction Decision Conditions
During operating of cooling and heating, when IPM temperature data (100
During operating of cooling and heating, when IPM temperature data (100
°C) is detected by the IPM temperature sensor.
Multi Models Only
• Compressor Overheating: During operation of cooling and heating, when the compressor OL is activated.
• Heat Sink Overheating: During operation of cooling and heating, when heat sink temperature data (90°C) is detected by the heat
• Heat Sink Overheating: During operation of cooling and heating, when heat sink temperature data (90°C) is detected by the heat
sink temperature sensor.
Malfunction Caused
• IPM overheats due to short circuit of hot discharge air flow.
• IPM overheats due to defective of outdoor fan motor.
• IPM overheats due to defective of internal circuitry of IPM.
• IPM overheats due to defective IPM temperature sensor.
• IPM overheats due to defective of outdoor fan motor.
• IPM overheats due to defective of internal circuitry of IPM.
• IPM overheats due to defective IPM temperature sensor.
Multi Models Only
• Compressor OL connector poor contact.
• Compressor OL faulty.
• Compressor OL faulty.
Troubleshooting
80
15.5.21. F97 (Compressor Overheating)
Malfunction Decision Conditions
During operation of cooling and heating, when compressor tank temperature data (112°C) is detected by the compressor
tank temperature sensor.
During operation of cooling and heating, when compressor tank temperature data (112°C) is detected by the compressor
tank temperature sensor.
Malfunction Caused
• Refrigerant shortage (refrigerant leakage).
• 2/3 way valve closed.
• Detection error due to faulty compressor tank temperature sensor.
• 2/3 way valve closed.
• Detection error due to faulty compressor tank temperature sensor.
Troubleshooting
Click on the first or last page to see other CS-E10JD3EA / U-E10HBEA / CS-E15JD3EA / CU-E15HBEA / CS-E18JD3EA / CU-E18HBEA service manuals if exist.