DOWNLOAD Panasonic CS-A28JKD / CU-A28JKD Service Manual ↓ Size: 5.64 MB | Pages: 64 in PDF or view online for FREE

29

• Automatic operation can be set using remote control.
• This operation starts to operate with indoor fan at SLo speed for 25 seconds to judge the intake air temperature.
• After judged the temperature, the operation mode is determined by referring to the below standard.

• Then, the unit start to operate at determined operation mode, until it is switched off using remote control, with the setting

temperature as shown in below table.

• Operation mode will be determine again for judgement after 1 hour of operation, if the room temperature reaches to set

temperature and compressor off time is over 7 minutes 30 seconds continuously.

*

The present operation mode will be continued, if the room temperature does not reach to set temperature (Compressor keeps

running) eventhough after 1 hour from automatic operation mode started.

• Automatic Set Temperature

For each operation, set temperature will automatically set as shown below.

• The setting temperature for all the operations can be changed one level up or one level down from the standard temperature as

shown in below table by pressing on the temperature up or temperature down button at remote control.

• The operation mode judging temperature and standard setting temperature can be increased by 2°C permanently, by open the

circuit of JX03 at printed circuit board indoor unit.

Present

Mode

Judgement

Next Mode

Cooling

Soft Dry

Heating

Cooling

O

(Judgement:

23

qC & Above)

Not Applicable

O

(Judgement:
Below 23

qC)

23

qC

Cooling

Heating

Soft Dry

Not Applicable

O

(Judgement:

20

qC & Above)

O

(Judgement:
Below 20

qC)

20

qC

Soft Dry

Heating

Heating

O

(Judgement:

25

qC & Above)

Not Applicable

O

(Judgement:
Below 25

qC)

25

qC

Cooling

Heating

Operation

Hi

(Standard)

Lo

(+2

qC)

(±0

qC)

(-2

qC)

Cooling

27

qC

25

qC

23

qC

Soft Dry

24

qC

22

qC

20

qC

Heating

23

qC

21

qC

19

qC

30

• Indoor Fan Speed can be set using remote control.

• When set to Auto Fan Speed, the fan speed is adjusted between maximum and minimum setting as shown in the table.

- Fan speed rotates in the range of Hi, Me and Lo-.
- Deodorizing Control will be activated.

Speed

CS-A28HKD

Cool, Dry

Heat

S Hi

Hi

1540

Hi

1500

Me

Me

1380

Lo+

Lo

1250

Lo

1030

Lo-

Lo-

810

S Lo

S Lo

300

SS Lo

300

Q SHi

Q Hi

1450

Q Hi

1410

Q Me

Q Me

1290

Q Lo

1160

Q Lo

1160

31

• Auto Fan Speed during Cooling operation:

1. Indoor fan will rotate alternately between off and on as shown in below diagram.
2. At the beginning of each compressor start operation, indoor fan will increase fan speed gradually for deodorizing purpose.
3. For the first time the compressor operate, indoor fan will be switched to Hi fan speed from Lo- after 70 seconds from the

start of compressor. This cause the room temperature to achieve the setting temperature quickly.

4. During compressor stop, indoor fan will operate at Lo- for the beginning 20 seconds to prevent higher volume of refrigerant

in liquid form returning to the compressor.

5. After the compressor at turn off condition for 3 minutes, indoor fan will start to operate at Lo- to circulate the air in the

room. 
This is to obtain the actual reading of the intake air temperature.

6. For the resume of compressor operation, indoor fan will operate at Me fan speed to provide comfort and lesser noise

environment, after 70 seconds from the restart of compressor.

• Auto Fan Speed during Soft Dry operation:

1. Indoor fan will rotate alternately between off and Lo-.
2. At the beginning of each compressor start operation, indoor fan will increase fan speed gradually for deodorizing purpose.
3. When compressor at turn off condition for 6 minutes, indoor fan will start fan speed at Lo- to circulate the air in the room.

This is to obtain the actual reading of intake air temperature.

• Auto Fan Speed during Heating operation.

1. Indoor fan will rotate in the range of SLo 

o Me according to the heat exchanger temperature.

32

• Manual fan speed adjustment can be carried out by using the Fan Speed selection button at the remote control.
• There are 3 types of fan speed settings: Lo, Me, Hi.

• There is 2 speed for outdoor fan motor. Outdoor fan speed can be changed to Hi or Lo according to outdoor temperature.
• For Cooling or Soft Dry operation when outdoor temperature reaches to 31

qC (Hi-speed), 29qC (Lo-speed).

• For Heating operation when outdoor temperature reaches to 13.5

qC (Hi-speed), 15.5qC (Lo-speed)

• When the air conditioner is turned on, the compressor and the outdoor fan will operate simultaneously.
• Likewise, both compressor and outdoor fan will stop at the same time if the unit is turned off.

• When the vertical airflow direction is set to Auto using the

remote control, the louver swings up and down as shown in
the diagram.

• When stopped with remote control, the discharge vent is

reset, and stop at the closing position.

• During Cooling operation or Soft Dry operation, indoor fan

motor may stop to rotate at certain periods. At that condition,
the louver will stop swinging and rest at the upper limit.

Cooling and Soft Dry Operation

• When the piping air temperature reaches 38°C, the
• louver is changed from upper to lower limit. When the
• piping air temperature falls to 35°C, the louver is changed

from lower to upper limit.

Heating Operation

• When the vertical airflow direction is set to Manual using the remote control, the automatic airflow is released and the airflow

direction louver move up and down in the range shown in the diagram.

• The louver can be adjusted by pressing the button to the desired louver position.
• When stopped with remote control, the discharge vent is reset, and stop at the closing position.

Cooling and Soft Dry Operation

Heating Operation