LG WT5101HW Service Manual ▷ View online
5
27″
(68.6 cm)
1″
(2.5 cm)
1″
(2.5 cm)
28.
13
/
64
″
(72.1 cm)
4″
(10 cm)
45.
13
/
32
″
(115.3 cm)
55.
13
/
16
″
(141.7 cm)
(with lid
open)
6
7
5
Lower
Raise
Confirming level
•
Place the washer in original position,
confirming the level.
confirming the level.
Horizontal setting
•
Lift the front of the washer and adjust
level by turnings the adjustable legs
clockwise or using the adjusting plate.
level by turnings the adjustable legs
clockwise or using the adjusting plate.
Distance between the drain hose
and the wall
•
Distance between the drain hose and
the wall should be more than 4 inches
(10 cm), and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm)
the wall should be more than 4 inches
(10 cm), and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm)
Do not install the washer in the following places.
•
Where the washer is exposed to direct sunlight.
•
Near a heater or heating appliance.
•
Where the washer is exposed to freezing temperatures.
•
In damp environments such as bathrooms or harmful environments.
1
Attach the water supply hose to the tap.
Push the water supply hose up so that the rubber packing
within the hose can adhere completely to the tap.
within the hose can adhere completely to the tap.
2
Connect the water supply hose to the tap.
Connect the water supply hose to the tap and then tighten it by
screwing it to the right.
screwing it to the right.
3
Check water leakage.
After connecting the hose, open the tap to check for
any water leakage.
any water leakage.
Check water leakage.
After connecting the hose, open the tap to check for
any water leakage.
any water leakage.
Connecting Water Supply Hose to the machine
• Connect the water supply hose to inlet valve of
the washing machine, and then lock it by turning
the hose connecting part.
the hose connecting part.
• Check to see if there is a rubber seal inside the
connector.
• A nwe washing machine should be instailed with new
hoses. The old hoses shuld not be reused.
Screw Type
Hot
Cold
Water tap
Rubber Seal
Water Supply Hose
Water Hose
(to water inlet
on washer)
(to water inlet
on washer)
Rubber Seal
Water Hose
(to tap)
(to tap)
Rubber Seal
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting the Water Supply Hose to the water tap, check the hose type and then choose the
correct instruction here under.
correct instruction here under.
7
2-3. CONNECT THE DRAIN HOSE
39" (99 cm)
39" (99 cm)
• Connect the drain hose to the
outlet of the drain pump located at
the rear of the washing machine.
the rear of the washing machine.
• Attach the clip to the drain hose.
And then push it toward the body of
the washing machine as indicated
by the arrow.
the washing machine as indicated
by the arrow.
• Check that the drain hose is hung
up over the edge of the laundry tub.
• Do not use an extension hose.
NOTE :
•
The drain hose should always be properly secured. Failure to properly secure the drain hose
can result in flooding and property damage.
can result in flooding and property damage.
• The end of the drain hose should be placed 39" (99 cm) from the floor.
• The drain must be installed in accordance with any applicable local codes and regulations.
• Make sure that the water lines are not stretched, pinched, crushed, or kinked.
• Do not insert the drain hose more than 12” (30 cm) into the drain pipe to avoid siphoning and
• The drain must be installed in accordance with any applicable local codes and regulations.
• Make sure that the water lines are not stretched, pinched, crushed, or kinked.
• Do not insert the drain hose more than 12” (30 cm) into the drain pipe to avoid siphoning and
odor build-up.
Cable Tie
Cable Tie
WARNING:
• The washer should never be installed or stored in a location subject to freezing temperatures. If the
washer was exposed to freezing temperatures prior to installation, allow it to stand at room
temperature for several hours before use Damage to the water lines and internal mechanisms of
the washer can result.
temperature for several hours before use Damage to the water lines and internal mechanisms of
the washer can result.
• Water supply pressure must be between 14.5 psi and 116 psi (100 ~ 800kPa) If the water supply
pressure is more than 116 psi, a pressure reducing valve must be installed. If you have
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that wate temperature and water pressure remain within the safe limits. Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure. Failure to do
so can result in damage to the machine.
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that wate temperature and water pressure remain within the safe limits. Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure. Failure to do
so can result in damage to the machine.
• Plug the power cord of washer into a properly grounded outlet. Failure to do this can result in shock
or serious injury.
8
3. OPERATING INSTRUCTION
3-1. IDENTIFICATION OF PARTS
Powder detergent
Box for delayed
washing/softener additves box
Box for delayed
washing/softener additves box
INLET HOLE FOR
BLEACH
BLEACH
Clean regularly to stop
linting on the clothes
load.
linting on the clothes
load.
Washing Wing
(unique with lnner Tub)
(unique with lnner Tub)
LEVELLING LEGS
Use to level the washing
machine for correct balance
spin operation.
Use to level the washing
machine for correct balance
spin operation.
Multi Clean filter
TUB
HOT WATER SUPPLY
HOSE
HOSE
COLD WATER SUPPLY
HOSE
Make sure the water
does not leak.
HOSE
Make sure the water
does not leak.
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer
or its service agents
or similarly qualified
person in order to
avoid a hazard.
If the supply cord is
damaged, it must be
replaced by the
manufacturer
or its service agents
or similarly qualified
person in order to
avoid a hazard.
FUNCTION SELECTOR
BASE
DRAIN HOSE
Be sure the drain hose
is properly installed on
the drain before
operating the washer.
Be sure the drain hose
is properly installed on
the drain before
operating the washer.
Click on the first or last page to see other WT5101HW service manuals if exist.