LG WT5070CW Service Manual ▷ View online
5
28.
13
/
64
″
(72.1 cm)
4″
(10 cm)
55.
13
/
16
″
(141.7 cm)
(with lid
open)
6
7
5
Lower
Raise
Confirming level
•
Place the washer in original position,
confirming the level.
confirming the level.
Horizontal setting
•
Lift the front of the washer and adjust
level by turnings the adjustable legs or
using the adjusting plate.
level by turnings the adjustable legs or
using the adjusting plate.
Distance between the drain hose
and the wall
•
Distance between the drain hose and
the wall should be more than 4 inches
(10 cm,) and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm.)
the wall should be more than 4 inches
(10 cm,) and the distance between any
other part and the wall should be more
than 1 inches (2.5 cm.)
Do not install the washer in the following places.
•
Where the washer is exposed to direct sunlight.
•
Near a heater or heating appliance.
•
Where the washer is exposed to freezing temperatures.
•
In damp environments such as bathrooms or harmful environments.
1
Be sure there is a gasket in both ends of the hose.
Push the water supply hose up so that the rubber packing
within the hose can adhere completely to the tap.
within the hose can adhere completely to the tap.
2
Connect the water supply hose to the tap.
Run a couple of gallons of water through the hoses into the drain or a
bucket to flush any particulate or contaminate.
bucket to flush any particulate or contaminate.
3
Check water leakage.
After connecting the hose, open the tap to check for
any water leakage.
any water leakage.
Connecting Water Supply Hose to the Machine
• Be sure there is a gasket in the end of the hose.
• Connect the hose to the appropriate inlet vale
(hot or cold) of the washing machine and tighten
if firmly.
if firmly.
• Turn on the water and check for leacks.
• Always install new hoses with a new washing
machine Do not re-use old hoses.
• Relplace the hoses every five years.
Screw Type
Water tap
Rubber Seal
Water Supply Hose
Cold water inlet
Hot water inlet
2-2. CONNECTING WATER SUPPLY HOSE
6
Before connecting the water supply hose to the water tap, check the hose type and then choose the
correct instruction here below.
correct instruction here below.
7
2-3. CONNECT THE DRAIN HOSE
35"~47" (0.9~1.2m)
35"~47" (0.9~1.2m)
• Connect the drain hose to the
outlet of the drain pump located at
the rear of the washing machine.
Attach the clip to the drain hose.
the rear of the washing machine.
Attach the clip to the drain hose.
• And then push it toward the body of
the washing machine as indicated
by the arrow.
by the arrow.
• Check that the drain hose is hung
up over the edge of the laundry tub.
• Do not use an extension hose.
NOTE :
•
The drain hose should always be properly secured to the drain or standpipe. Failure to secure
the drain hose properly can result in flooding and property damage.
the drain hose properly can result in flooding and property damage.
• The end of the drain hose should be placed 39" (99 cm) above the floor.
• The drain must be installed in accordance with any applicable local codes and regulations.
• Make sure that the water lines are not stretched, pinched, crushed, or kinked.
• Do not insert the drain hose more than 12” (30 cm) into the drain pipe to avoid siphoning and
• The drain must be installed in accordance with any applicable local codes and regulations.
• Make sure that the water lines are not stretched, pinched, crushed, or kinked.
• Do not insert the drain hose more than 12” (30 cm) into the drain pipe to avoid siphoning and
odor build-up.
Cable Tie
Cable Tie
WARNING:
• The washer should never be installed or stored in a location subject to freezing temperatures. If the
washer was exposed to freezing temperatures prior to installation, allow it to stand at room
temperature for several hours before use. Damage to the water lines and internal mechanisms of
the washer can result.
temperature for several hours before use. Damage to the water lines and internal mechanisms of
the washer can result.
• Water supply pressure must be between 14.5 psi and 116 psi (100 ~ 800kPa) If the water supply
pressure is more than 116 psi, a pressure reducing valve must be installed. If you have
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that water temperature and water pressure remain within the safe limits. Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure. Failure to do
so can result in damage to the machine.
uncontrolled water temperature and pressure you should fit a temperature and pressure relief valve
to ensure that water temperature and water pressure remain within the safe limits. Consult a
plumber or electrician if you are unable to adjust water temperature and or pressure. Failure to do
so can result in damage to the machine.
• Plug the power cord of washer into a properly grounded outlet. Failure to do this can result in shock
or serious injury.
8
3. OPERATING INSTRUCTION
3-1. IDENTIFICATION OF PARTS
POWDER DETERGENT
BOX for delayed
washing/softener additves box
BOX for delayed
washing/softener additves box
INLET HOLE FOR
BLEACH
BLEACH
WASHING WING
(unique with lnner Tub)
(unique with lnner Tub)
LEVELLING LEGS
Use to level the washing
machine for correct balance
spin operation.
Use to level the washing
machine for correct balance
spin operation.
TUB
COLD WATER SUPPLY
HOSE
HOSE
HOT WATER SUPPLY
HOSE
Make sure the water
does not leak.
HOSE
Make sure the water
does not leak.
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer
or its service agents
or similarly qualified
person in order to
avoid a hazard.
If the supply cord is
damaged, it must be
replaced by the
manufacturer
or its service agents
or similarly qualified
person in order to
avoid a hazard.
FUNCTION SELECTOR
BASE
DRAIN HOSE
Be sure the drain hose
is properly installed on
the drain before
operating the washer.
Be sure the drain hose
is properly installed on
the drain before
operating the washer.
SMART RINSE WITH
JET SPRAY
This washer is designed
to save rinse water by
using a jet spray rinse
system in the
Normal/Casual and
Heavy Duty cycles.
JET SPRAY
This washer is designed
to save rinse water by
using a jet spray rinse
system in the
Normal/Casual and
Heavy Duty cycles.
Click on the first or last page to see other WT5070CW service manuals if exist.