LG WT-R9000TH Service Manual ▷ View online
4-4. DISASSEMBLY INSTRUCTION
32
Be sure to unplug the power to repair and
replace electric parts.
replace electric parts.
Asegúrese de hacer conexión a tierra para los
diagnósticos de problemas y reemplazo de partes.
Si no es posible, toque un cable a tierra con su
cuerpo para remover la desviación eléctrica entre
el cuerpo y el producto antes de trabajar.
diagnósticos de problemas y reemplazo de partes.
Si no es posible, toque un cable a tierra con su
cuerpo para remover la desviación eléctrica entre
el cuerpo y el producto antes de trabajar.
PRECAUCIÓN POR ELECTROSTÁTICA
1) Disassembly of Front Panel
& PWB Assembly
Remove two screw caps using a sharp tool
and two front panel fixing screws.
and two front panel fixing screws.
Push the front panel to the left side then
pull it out.
pull it out.
Disconnect the leads from the controller.
Remove 4 screw from the front panel.
Remove the PWB Assembly.
Fuse is located in the PCB assembly For fuse
replacement use the following rated fuse
* Rating of fuse
replacement use the following rated fuse
* Rating of fuse
- 250V 6A fusing type for 220-240V product
- 125V 12A fusing type for 100-127V product
- 125V 12A fusing type for 100-127V product
PWB Assembly
leads
Fuse
33
2) Disassembly of Back Panel, Power
Cord, Inlet Valve & BP Sensor
Remove two back panel fixing screws in the
back side.
back side.
Disassemble the back panel.
Disconnect two connectors and disassemble
the power cord.
the power cord.
Remove a valve fixing screw & disconnect the
leads form the inlet valve.
leads form the inlet valve.
Remove the inlet valve.
Disconnect the leads & the pressure tube from
the BP sensor.
the BP sensor.
Remove the BP sensor.
3) Disassembly of Lid Assembly
& Top Cover
Remove Q-spring & two hinge pins then
disassemble the lid assembly
disassemble the lid assembly
Remove two top cover fixing screws in the
rear then disassemble the top cover.
rear then disassemble the top cover.
Lid Hinge
Inlet valve
Power cord
BP sensor
Q-spring
Location P/No. PIVOT(Color)
K101
NATURAL
34
Pulsator
5) Disassembly of Back Cover, Drain Pump,
Clutch(Transmission) & Motor
Remove back cover fixing screws then disassemble
the back cover.
the back cover.
Disconnect the leads and the drain hose-p from the
drain pump.
drain pump.
Remove the pump fixing screws then
disassemble the drain pump.
disassemble the drain pump.
Fall down the washer for clutch & motor removal.
Remove the belt.
Disassemble the clutch.
Remove two motor fixing screws then
disassemble the motor.
disassemble the motor.
6) Replacement of Damper asm
Separate top cover from washing machine.
As in the fig, lift snubber bar and take it out of out
case with out tub.
case with out tub.
Damper assembly shall not be disassembled.
Replace damper as assembly.
Replace damper as assembly.
For assembly, keep the following. (Location & color)
Tub cover
Inner tub
Hub fixing nut
Leads
Drain hose
Pump fixing screw
4) Disassembly of Tub Cover,
Pulsator & Inner Tub
Remove tub cover fixing screws then
disassemble the tub cover.
disassemble the tub cover.
Remove the pulsator fixing screw then
disassemble the pulsator.
disassemble the pulsator.
Remove the hub fixing nut by a special tool.
Disassemble the inner tub.
35
7) Replacement of Clutch Housing Asm
Disassemble the Clutch Housing Asm bolt
with boxer or spanner. (M12)
(
with boxer or spanner. (M12)
(
Before disassemble the Clutch Housing
Asm, disassemble the Brake Motor)
Asm, disassemble the Brake Motor)
Pulsator Revolving Cam
Clutch
Clutch Housing Asm
Brake Motor
Stator
Rotor
Clutch
Motor
Pulsator
Inner Tub
Outer Tub
Brake
Motor
• Type ‘A’ : Apply to
less than
8.0kg model
8.0kg model
• Type ‘B’ : Apply to
more than
9.0kg model
9.0kg model
Click on the first or last page to see other WT-R9000TH service manuals if exist.