DOWNLOAD LG WT-R107 Service Manual ↓ Size: 4.57 MB | Pages: 55 in PDF or view online for FREE

SNAP RING.

Clutch Motor

Clutch Motor

Hall Sensor

Stator Housing

Water Guide

Clutch Motor

Clutch Motor

Coupling ASM

Loosen the 6 fixing screws on the stator. 
(Lower 

upper position screws)

Check the direction of SNAP RING.
(The handle of snap ring is toward to rotor and stator.)

Preventing fallen the stator, tighten with one hand and
then loosen the last screw.

For assembly take care lead wire's state, it produce a
noise and cut attach the rotor.

Loosen 16 Fixing screws on the Bearing Housing ASM
and pull it up.
Loosen 2 Fixing screws on the Clutch Motor and pull it
up.

To use the CHECK PROGRAM (QC TEST MODE), press WASH/RINSE, SPIN SPEED and POWER button
ON without depositing any laundry.

START(PAUSE) button to check over the following items.

NO

CHECK METHOD

DISPLAY

CHECK ITEM

REMARKS

1

2

3

4

5

6

7

9

8

11

Initial state

Press once

Press twice

Press 3  times 

Press 4  times

Press 5  times

Press 6  times

Press 7  times

Press 8  times

Press 10  times

12

Press 11  times

Load Value / t5

After detecting laundry amount ,
Spin ON.

Test Mode Start

t1/HA

t2

Version/t2

t3

Water Level Frequency / A

Water Level Frequency / b

All LEDS ON

ALL LEDS OFF

ALL LEDS OFF

Chech each of buttons except

“Power” and “Start”

COLD Water ON. (Boost Dispenser,

Bleach Dispenser)

COLD Water ON. (Softener

Dispenser)

Water Level Frequency / C

t4

Water Level Frequency / t4

t5

13

Press 12  times

15

Press 14  times

t7

Spin

t6

COLD water and HOT Water ON.
(Detergent Dispenser)

DRAIN PUMP ON.

Ex)       = 333            = 233
If there is no load it may
display above 300.

14

Press 13  times

16

Press 15  times

Error or nE / t7

Error

It display previous error.
If there is no error bofore it will
display “

nE

”

RPM / t6

17

Press 16  times

OFF

ALL LEDS OFF

10

Press 9 times

ALL LEDS OFF

ALL LEDS OFF

ALL LEDS OFF

ALL LEDS OFF

Many washing problems involve poor soil & stain removal, residues of lint and scum, and fabric damage. For
satisfactory washing results, follow these instructions.

Poor soil
removal

Blue Stains

Black or gray
marks on
clothes

Yellow or
brown rust
stains

Lint

Residue or
Detergent

Holes, tears,
or snags

Undiluted fabric softener
dispensed directly onto fabric

A buildup caused by the interaction
of fabric softener and Detergent
can flake off and mark clothes
Not enough Detergent

Iron or manganese in water
supply, water pipes, or water
heater

ncorrect sorting
Tissues left in pocket 
Overloading the washer

Overloading the washer
Undissolved Detergent
Use too much Dtergent

Incorrect use of chlorine bleach.
Unfastened zippers, hooks,
buckles 
Ribs, tears and broken threads
Overloading the washer
Degradation of fabric

Not enough Detergent
Wash Water Temperature too low.
Overloading the washer
Incorrect wash cycle
Incorrect sorting
Do not pretreat stain.

Use correct amount of Detergent for load size, amount of soil and
water Hardness.
Use WARM or HOT water for normal soil. Different Water
Temperature may be required according to soil type. 

Reduce load size.
Wash with Heavy or Soak & Heavy wash cycle for heavy soiled
laundry.
Separate heavily soiled items from lightly soiled ones.
Pretreat stain and heavy soil according to directions shown on 
page 11.

Rub the stain with bar soap Wash.
Do not overfill fabric softener dispenser and do not pour liquid fabric
softener directly onto fabric. 
See page 14 for more instructions.

Keep the recommendations against Scrud(waxy buildup).
Use correct amount of Detergent for load size, amount of soil
and water Hardness.

To restore discolored load of whites, use rust remover safe for
fabric.
Install nonprecipitating water softener or an iron filter in your
water supply system for an ongoing problem.
Before washing, run water for a few minutes to clear lines.

Wash lint givers eg towels, flannelette sheets, separately from
lint collectors e.g. synthetic fabrics and remove tissues in
pockets before wash. See page 11 for sorting and caring before
loading.
Do not overload the washer

Do not overload the washer.
Some Detergents need to be pre-dissolved, check the
Detergent instructions. Try pre-dissolving the Detergent.
Increase Water Temperature using HOT water safe for fabric.
Use proper amount of Detergent.

Never pour chlorine bleach directly on fabric.
See page 13 for adding liquid bleach.
Fasten zippers, hooks, and buckles.
Remove objects in pockets. See page 11 for caring before loading.
Do not overload the washer.

For more detailed information for trouble shooting refer to page 42 to 51.

ERROR

WATER

SUPPLY 

DRAINAGE

UNBALANCE

DOOR 

OPEN

WATER LEVEL
dose not rise to
the set level in 40
minutes.

Water is not
completely
drained in 13
minutes.

Laundry
unbalance during
spin.

LID is opened in
course of
operation or
processing reser
vation.

1. Drain hose is hung on to

drainage which is 0.9m
above from floor.

2. Water faucet is closed?
3. Water supply is interrupted.
4. Inlet V/V is clogged with

dirts.

5. Connector has bad contact

to the inlet valve.

6. BLUE 6 pin connector has

bad contact to the P.W.B
ASM.

1. Is the drain hose located

properly?

2. Drain hose is folded or

clogged due to freeze or dirt.

3. Bad Drain Pump part or

BLUE (WHITE) 2 pin
connector to the P.W.B ASM
has bad connection.

1. Laundry in the INNER TUB

is filled unevenly.

2. Washer is tilted.

1  Lid is opened during

intermittent spin or normal
spin?

2  Lid is opened while

processing reservation?

3. Bad lead wire ASM or

Connector to the Lid S/W or
RED 4pin connector to the
P.W.B ASM has bad
connection.

1. Hang drain hose which is

minimum 0.9m above from
floor.

2. Open water faucet.
3. Wait until water supply is

resumed.

4. Clean or replace filter.
5. Correct the connector

contact.

6. Same as above.

1. Hung up drain hose at

0.9~1.2m high.

2. Unclose the foreign objects

within drain hose.

3. Replace Drain Motor or

correct the connector
contact.

1. Try to fill laundry uniformly in

the inner tub.

2. Adjust the leg.

1. Closed the lid.

2. Closed the lid.

3. Check and replace Lead

Wire ASM or Correct the
connector contact.

ERROR DECISION

BASIS

CAUSE FOR ERROR

OCCURRENCE

REMEDY