DOWNLOAD LG WP-9251 Service Manual ↓ Size: 8.16 MB | Pages: 28 in PDF or view online for FREE

Remove the Spin Motor by removing the screws
fastening the vibration damper assemblies (Fig. 26)

7.

4-4. Spin Motor replacement

Remove the brake wire holder-A in the direction of
the arrow(Fig. 22.).

1.

After removing the back cover, opening the spin dryer
cover, and removing the spin dryer basket, proceed
as follows:

Separate the brake wire assembly from the brake
strap assembly (Fig. 23).

2.

Take out the brake wire assembly from the brake
assembly (Fig. 24).

3.

Disconnect the lead wires and remove the V-belt.

4.

Lay the washing machine on its front side on a
blanket or cardboard.

5.

Remove the screws fastening the base and remove
the base from the outcase (Fig. 25).

6.

Fig. 25

Fig. 26

-9-

Fig. 22

Fig. 23

Fig. 24

8.

Fig. 27

Fig. 28

Fig. 29

Fig. 30

Fig. 31

Fig. 32

Loosen the fixing bolt fastening the motor shaft
and pull up the coupling assembly (Fig. 27).

9. Remove the screws fastening the brake assembly

and remove the brake assembly (Fig. 28).

To assemble the spin motor, reverse the disassembly
procedure.

4-5. Wash Motor replacement

After removing the back cover and the spin dryer
basket, proceed as follows:

1. Remove the V-belt from the pulsator pulley (Fig. 29).

2. Disconnect the lead wires.

3. Lay the washing machine on its front side on a

blanket or cardboard.

4. Remove the screws fastening the base and remove

the base from the outcase (Fig. 30)

5. Remove the screws and the washers, remove the

wash motor and remove the wash motor
damper (Fig. 31).

6. Loosen the socket bolt of the motor pulley

assembly and pull up the motor pulley assembly
from the motor (Fig. 32).

To assemble the wash motor, reverse disassembly
procedure.

-10-

Fig. 33

Fig. 34

Fig. 35

Fig. 36

Fig. 37

4-6. Washing Tub Assembly
       replacement

After removing the panel assembly, the safety cover
assembly, the spin dryer basket assembly, the spin
dryer cover, the washing cover, the Q-spring, the
nozzle case, the door switch and the back cover,
proceed as follows:

1. Disconnect the drain hose.

2. Remove the V-belt from the pulsator pulley (Fig. 33).

3. Remove the screws fastening the washing tub

assembly and pull it out (Fig. 34).

To assemble the washing tub assembly, reverse
the disassembly procedure.

Apply adhesive on hose joint to prevent
water leaks.

NOTE

4-7. Gear Case Assembly
       replacement

Loosen the pulsator fixing screw and pull up the
pulsator (Fig. 35).

1.

After removing the back cover and opening the
washing cover, proceed as follows:

Remove the V-belt

2.

Lay the washing machine on its front side on a
blanket or some cardboard.

3.

Unscrew and remove the screws fastening the base
and remove the base assembly (Fig. 37).

4.

-11-

7.

Fig. 38

Fig. 39

Fig. 40

Fig. 41

Fig. 42

6. Unscrew the pulsator pulley fixing bolt and remove

the pulsator pulley(Fig. 38).

Unscrew and remove the screws fastening the gear
case assembly at the tub(Fig. 39).

1.

Don't disassemble four screws fixing the

gear case assembly.

2.

Check the assembled condition of the

packing-P at the tub hole is right when you

assembled the gear case assembly (fig. 40).

4-8. Bellows Assembly Replacement

The bello

ws assemb

ly attached to the unit

cannot be remo

ved unless it is tor

n off.

After removing the spin dryer basket assembly, refer
to the figures and proceed as follows:

Remove the bellows assembly (Fig. 41).

1.

Remove the bellows supporter by using slip joint
pliers to the spin tub bottom (Fig. 41).

2.

Bellows assembly

Insert the bellows assembly into the bellows
supporter (Fig. 42).

1.

The assembly procedure is as follows:

Fit them by pushing the bellows assembly and the
bellows supporter at the same time in the spin tub
bottom (Fig. 42).

2.

Pass the spin shaft through the center hole of the
bellows assembly and insert it into the coupling
assembly (Fig. 42).

2.

-12-