DOWNLOAD LG WP-890R Service Manual ↓ Size: 7.44 MB | Pages: 27 in PDF or view online for FREE

5

(1) Wash Cover

(2) Water Supply Selector

(3) Over Flow Filter

(4) Rotation Filter-C

(5) Water Fall

(6) Tub(Cabinet)

(7) Roller Pulsator

(9) Spin dryer cover

Spinning will stop if the cover is opened

during operation.

Spinning will not start unless the cover is

closed.

(8) Drain Hose

(11) Spin Dryer Basket

(10) Safety Cover-1

(12) Earth Wire

(only on models with a two-prong plug)

(13) Stainer

(14) Power Cord

(1) Water supply inlet: Connect the inlet hose from the water faucet to feed water to the tub.

(2) Wash Timer: Select the desired time for washing or rinsing.

(3) Wash Program: Set the selector to "GENTLE", "NORMAL", "STRONG" according to kinds and quantity of the laundry.

(4) Drain Selector

   Non pump model : Select "WASH-RINSE" for washing and rinsing, and "drain" to drain the water out of the wash tub.

   Pump model : Select "WASH-RINSE" for washing and rinsing with an overflow drain, and "DRAIN" to drain the water

out of the wash tub, and "OFF" to turn off the drain pump.

(5) Spin Timer: Select the desired time for spinning.

(6) Water Selector: Set the supply select lever to "WASH" for washing and rinsing, to "SPIN" for interim spin rinse.

1

8

9

10

11

12

13

14

2

3

4

5

6

7

WASH

Spin Timer

Drain Selector

Wash Program

Water Selector

Wash Timer

2

3

4

5

6

1

Off

WASH

Spin Timer

Drain Selector

Wash Program

Water Selector

Wash Timer

2

3

4

5

6

1

6

1. Remove the screw fastening the back cover (Fig. 1).

Before attempting to replace or adjust any part of the washing machine, disconnect the electrical

power supply from the wall outlet.

¥ When replacing the panel assembly, fix the

plunger valve strap properly.

¥ Securely solder connecting lead wires, or

used connectors and insulate well to

prevent overheating.

5. Remove the screws fastening the panel (Fig. 5).

6. Lift up the panel assembly and lay it down on the top (Fig. 6).

To assemble the panel assembly, reverse the disassembly procedure.

1. Pull out the knobs (Fig. 7).

2. Pull out the supply select hose from the supply select

guide (Fig. 8).

Supply select guide

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 1

Fig. 2

2. Pull out the back cover (Fig. 2).

3. Remove the vinyl tape fastening the lead wires

closed connector to the plunger valve assembly and

disconnect the lead wires (Fig. 3).

4. Disconnect the plunger valve strap from the plunger

valve rod (Fig.4).

2. Remove the screws and separate the switch body

from the panel (Fig. 11).

3. Remove the spin timer by pushing the claw holding

the spin timer in the direction of the arrow (Fig. 12).

To assemble the timers to the switch body, reverse
the disassembly procedure.

❒  

1. Pull out the terminals and remove the screw fastening

the mini switch (Fig. 15).

2. Separate the mini switch from the switch body (Fig. 15).

To assemble the mini switch to the switch body,
reverse the disassembly procedure.

❒  

1. Pull out the knobs (Fig. 10).

To assemble the drain select arm to the switch body,
reverse the disassembly procedure.

the same time rotate the drain select arm in the direction
of the white arrow until the hook of the drain select arm
matches the groove of the switch body (Fig. 14).

❒  

1. Disconnect the plunger valve strap from the drain

select arm (Fig. 13).

Back side

Front side

4. Remove the screw fastening the cycle timer, pull

out the terminals from the buzzer and remove the
cycle timer(Fig. option1).

Fig. option

3. Remove the switch body from the panel.

4. Push the supply selector guide in the direction of

the arrow (Fig. 9).

To assemble the water supply system to the switch
body, reverse the above disassembly procedure.

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Fig. 13

Fig. 14

Fig. 15

After removing the back cover, proceed as follows:

1. Take hold of the front of the safety cover-1. 
2. Insert screw drive (

 - T

ype) into the hook position.

3. Pull the safety cover-1 upward (fig. 19).

2. Remove the Q-spring (Fig. 17).
3.Remove the screw fastening the door switch and

remove the door switch (Fig. 17).

4. Remove the spin dryer cover by widening between the

hinge hole of the top cover and the hinge of the spin

dryer cover and pulling up the spin dryer cover (Fig. 18).

5. Loosen the fixing bolt of the coupling assembly

fastening the spin shaft (Fig. 20).

6. Pull out completely the spin basket assembly (Fig. 21).

To assemble the spin dryer cover assembly, reverse

the disassembly procedure.

To assemble the spin dryer basket assembly, reverse

the disassembly procedure.

Fig. 18

Fig. 17

Fig. 16

Fig. 19

Fig. 20

Fig. 21

8

After removing the back cover, the panel assembly,

proceed as follows:

1. Open the spin dryer cover and separate  brake wire

strap from the brake wire assembly (Fig. 16).