DOWNLOAD LG WP-680N Service Manual ↓ Size: 4.14 MB | Pages: 23 in PDF or view online for FREE

-9-

3. Untigten the M-30 nut fastening the pulsator

shaft assembly. (fig.21)

To assembly the pulsator shaft assembly, reverse

the disassembly procedure.

After seprating the panel assemble, the safety cover

assembly, the spin dryer basket assembly, the spin

dryer cover, the drain hose, the drain hose-D

(For pump model) and the back cover, proceed

as follows:

To assemble the tub assembly, reverse the

disassembly procedure.

After separating the tub assembly, proceed as follows:

1. Untighten the pulsator fixing screw and separate

the pulsator from the tub. (fig.19)

2. Lay the tub assembly on a blanket or some

carboard and untighten the bolt fastening the

pulsator shaft and pull out the pulsator pulley.

(fig.20)

2. Untighten 10 screws and separate the tub

assembly from the cabinet. (fig.18)

fig.19

fig.20

fig.18

fig.21

1.Separate the V-belt from the pulley.(fig.17)

fig.17

V-belt

Pulsator fixing

screw

M-30 nut

-10-

1.Untighten the plunger valve cover by rotating in

the direction of the arrow. (fig.25)

The bellows assembly attached to the unit cannot be
separated unless it is torn off.

4. Tighten the bolt of the coupling assembly while

adjusting it to the cutter split made in the spin shaft.
(fig.24)

The assembly procedure is as follows:

1.Insert the bellows assembly into the bellows

supporter.

2.Fit them by pushing the bellows assembly and

the bellows supporter at the same time in the
spin tub bottom. (fig.23)

3.Pass the spin shaft through the center hole of the

bellows assembly and the insert it into the coupling
assembly. (fig.23)

fig.23

fig.25

1.Remove the belllows assembly. (fig.22)
2.Remove the bellows supporter by using slip joint

pliers to the tub bottom. (fig.22)

fig.22

fig.24

If the leakage occurs at the spin tub after
assembling the bellows assembly and the bellows
supporter, it is wrong. It could cause an electrical
shock  or a fire, therefore they should be securely
assembled again.

After separating the plunger valve strap from the
rod proceed as follows:

Bellows assembly

Plunger
valve cover

-11-

2.After separating the tub assembly from the

cabinet, untighten the screw to separte the

pump assembly from the cabinet. (fig.28)

When replacing the plunger valve assembly, take

care not to cause water leakage.

fig.27

2.Separate the cover, the spring, the rod and the

bellows from the plunger valve case. (fig.26)

fig.26

fig.28

Apply adhesive or use hose clamps on all joints to

prevent water leaks.

1.Separate all hoses (the drain hose-D, and the

outlet hose assembly) from the drain pump

assembly. (fig.27)

To assemble the plunger valve assembly, reverse

the disassembly procedure.

To assemble the drain pump assembly, reverse the

disassembly procedure.

Drain hose-D

Outlet hose assembly

Cover
Spring

Bellows

-12-

After separating the tub assembly from the cabinet,
proceed as follows:

4. Untighten the fixing bolt, fastening the motor shaft

and pull out the coupling assembly. (fig.31)

3. To separate the spin motor from the vibration

damper assemblies, untighten 3 screws. (fig.30)

1. Lay the washing machine on its front side on a 

blanket or cardboard.

2. To separate the spin motor assembly from the

cabinet, hold the spin motor and push the 3
hooks in the direction of the arrows. (fig.29)

5. Untighten 3 screws and separate the brake

assembly from the spin motor. (fig.32)

fig.32

fig.31

fig.29

In case of replacing the spin motor, the coupling
assembly must be exchanged with new one.

To assemble the spin motor, reverse the
disassembly procedure.

After separating the tub assembly from the cabinet,
proceed as follows:

1. To separate wash motor assembly from the

cabinet, untighten 3 screws. (fig.34)

fig.33

2. Separate the screws, the washers and the

dampers from the wash motor assembly. (fig.34)

fig.34

fig. 30

Brake assembly

Coupling assembly