DOWNLOAD LG WP-680N Service Manual ↓ Size: 4.14 MB | Pages: 23 in PDF or view online for FREE

-5-

(1) Washing cover

(2) Control panel

(3) Overflow filter

(4) Wash tub

(5) Strainer

(6) Pulsator

(7) Cabinet

(8) Spin dryer cover

Spinning will stop if the cover is

opened during operation.

Spinning will not start unless the cover is closed.

(9) Safety cover-2

(10) Spin dryer basket 

(11) Safety cover-1

(12) Earth wire

(only for models with a two-prong plug except for

rating voltage "110~120V")

(13) Drain hose (Non pump model)

(14) Power cord

(15) Drain hose (Pump model)

(1) Water inlet : Used to feed water to tub.

(2) Wash timer : Used to select wash time.

(3) Drain selector

• Model WP-581N/582N : Select "WASH&RINSE" for washing and rinsing, and "DRAIN" to drain the wash tub.

• Model WP-581NP/582NP : Select "WASH&RINSE" for washing and rinsing with an overflow drain, 

and "DRAIN" to drain the wash tub, and "OFF" to turn off the drain pump.

(4) Spin timer : Used to select spin time.

(15)

(10)
(11)

(12)
(13)

(14)

(8)

(2)

(3)
(4)

(5)

(6)
(7)

(1)

(9)

(for pump model)

1

2

3

4

5

3

6

9

12

15

OFF

OFF

For pump model

SPIN TIMER

DRAIN SELECTOR

WASH TIMER 

OFF

DRAIN

WASH¥RINSE

1

2

3

4

-6-

1.After untightening 3 screws, separate the back cover

from  the cabinet.(fig.1)

2.Unwind the vinyl tape and disconnect the lead 

wires. (fig.2)

4. Untighten 5 screws and separate the panel

assembly from the tub.(fig.4)(fig.5)

To assembly the panel assembly, reverse the
disassembly procedure.

3.Separate the plunger valve strap the rod.(fig.3)

fig.1

fig.4

fig.5

Before attempting to service or adjust any part of
the washing machine, disconnect the electrical
power supply from the wall outlet.

Back cover

fig.2

fig.3

Plunger valve strap

Rod

-7-

To assemble the drain select arm to the switch
body, reverse the disassembly procedure.

fig.6

fig.9

fig.10

fig.7

Timer Replacement

1. Pull out the knobs. (fig.6)

2.Untighten 4 screws and separte the switch body 

from the panel. (fig.7)

3.Separate the times from the switch body by

pushing the claw holding the times in the
direction of the arrow. (fig.8)

fig.8

To assemble the timers to the switch body, reverse
the disassembly procedure.

1.Pull out the knob.
2.Separate the plunger valve strap from the drain

select arm. (fig.9)

3.Lift the  A  of the drain select arm in the direction

of arrow and at the same time rotate the drain select
arm in the direction of the white arrow until the hook of
the drain select arm matches the groove of the switch
body.(fig.10)

Spin timer

Switch boby

Wash timer

Drain select arm

Plunger valve strap

-8-

3. Pull out completely the spin dryer basket 

assembly.(fig.16)

fig.11

To assemble the spin dryer basket assembly,

reverse the disassembly procedure.

1. Untighten the screw and separte the mini switch

from the switch body.(fig.11)

To assemble the mini switch to the switch body,

reverse the disassembly procedure.

2. After separating the Q-spring  and the door switch

from the tub pull out the spin dryer cover by

pushing the hook on the tub in the direction of

the arrow.(fig.13)

To assemble the spin dryer cover, reverse the

disassembly procedure.

After removing the back cover, proceed as follows:

1.Separate the spin dryer cover assembly from the

tub by pulling the part  A in the direction of

the arrow.(fig.14)

2.Loosen the bolt fastening the spin shaft.(fig.15)

1. Open the spin dryer cover and separate the brake

wire strap from the brake wire assembly.(fig.12)

After separating the panel assembly  from the tub,

proceed as follows:

fig.14

fig.15

fig.12

fig.16

fig.13

Brake wire

assembly

Brake wire strap

Q-spring

Door switch

Safety cover-1

A

Spin motor