DOWNLOAD LG WM3070HVA Service Manual ↓ Size: 18.46 MB | Pages: 61 in PDF or view online for FREE

1

2

3

4

5

6
7

Before servicing, ask the customer what the trouble is.
When installing or repairing the washer, put on long gloves and safety glasses.
Check the setup (power supply is 120 V

AC

, remove the transit bolts, level the washer, etc.)

Check with the troubleshooting guide.
Plan your service method by referring to the disassembly instructions.
Service the unit.
After servicing, operate the appliance to see whether it functions correctly.

STANDARD INSTALLATION

The appliance should be installed as follows:

Remove the 4 shipping bolts
with the supplied wrench.

આ

Remove the lower boits fist.
It is easier that way.

Keep the shipping bolts and
spanner for future use.
Insert the 4 caps (provided)
into the hole.

Turn clockwise to raise;
counterclockwise to lower. 

Turn the leveling feet to
adjust the appliance.

Lower

Higher

4. INSTALLATION & TEST

Keeping

Verify that the rubber washer is inside of the

valve connector.

Tighten the inlet hose securely to prevent leaks.

Install the inlet hose to correct temperature

water tap.

Otherwise, it cause drips on the drawer panel

handle and drawer panel.

HOW TO CONNECT THE INLET HOSE 

CONNECT THE DRAIN HOSE

• Make sure that the hose is not twisted.

CONNECT POWER PLUG

આ The end of the drain hose should be placed less than 96” from the floor.

• Avoid submerging the end of the hose.

• Connect the power plug to the wall outlet.

• Avoid connecting several electric devices, 

as doing so may cause a fire.

Hot

Cold

7 TEST OPERATION

Preparation for
washing.

• Connect the power plug to the

outlet.

• Connect the inlet hoses. 

Press the POWER button.

Press the START/PAUSE
button.

• Listen for a click to determine if the

door has locked.

Check the water heating
function.

• Press the WASH/RINSE button

and  the present temperature will
be displayed.

• Check if the drum rotates

clockwise and counterclockwise. 

Check the automatic reverse
rotation.

Check the water supply.

• Check if water is supplied through

the detergent dispenser.

Check the drain and spin
functions.

• Power off and the power on.
• Press the SPIN SPEED button.
• Press the START/PAUSE button.
• Check the spin and drain functions.

• Listen for a click to determine if the

door is unlocking.

Press the START/PAUSE
button.

Water removal

• If SERVICE is needed during

check, remove the remaining
water by pulling out the hose cap.

5. OPERATION

5-1. CONTROL PANEL FEATURES

Press to turn the washer ON. Press again to turn the washer OFF. 
NOTE: Pressing the ON/OFF button during a cycle will cancel that
cycle and any load settings will be lost.

Turn this knob to select the desired cycle. Once the desired
cycle has been selected, the standard presets will be shown in
the display. These settings can be adjusted using the cycle
setting buttons anytime before starting the cycle.

Press this button to START the selected cycle.

If the

washer is running, use this button to PAUSE the cycle without
losing the current settings. 
NOTE: If you do not press the START/PAUSE button within 4
minutes of selecting a cycle, the washer automatically turns off.

Press the STEAM button to add steam to the selected cycle
for added cleaning power.
NOTE: Steam can be added to only the following cycles:
STEAM FRESH™, ALLERGIENE™, SANITARY, BRIGHT
WHITES™, BULKY/LARGE, PERM. PRESS,
COTTON/NORMAL, HEAVY DUTY and TOWELS.

Press this button to delay the start of the wash cycle. Each
press of the button increases the delay time by one hour, up
to 19 hours.

The special function buttons allow you to select additional
functions and will light when selected. Certain buttons
also allow you to activate secondary functions by pressing
and holding the button for 3 seconds. For detailed
information about the individual functions, please see the
following pages.

Press this button to select additional cycle options such as
WATER PLUS, PRE WASH and ENERGY USAGE
DISPLAY.
Press the button next to the desired option in the display
to select. The button will light to show the option has been
selected.

The display shows the settings, estimated time remaining,
options, and status messages for your Steam Washer™.
The light in the display will remain on through the cycle.

Use these buttons to select the desired cycle options for
the selected cycle. The current options are shown in the
display. Press the button for that option to view and select
other settings.