DOWNLOAD LG WM3055CW Service Manual ↓ Size: 6.12 MB | Pages: 58 in PDF or view online for FREE

8-5. TROUBLE SHOOTING ELSE

1. Be careful of electric shock if disconnecting parts while troubleshooting.
2. First of all, check the connection of each electrical terminal with the wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, reinsert the connectors correctly.

Check the
fuse or reset
the circuit
breaker

Is the current rating of
multi-outlet power strip
enough?
(Avoid connecting several
electric devices.)

Is the supplied voltage
120V AC?(+10%, -15%)

Alternate with
explanation

Check the connectors at the
main PCB and the line filter.
Are the connectors loose or
disconnected? 

Reconnect
or repair
the connector

Replace the
MAIN PWB
ASSEMBLY

Main LED

Is LED on while the power
is on?

Replace the
DISPLAY
PWB
ASSEMBLY

Is three pin wire of
display PWB broken?

jŒŠ’G›ŒGŠ–••ŒŠ›–™šGˆ›G›Œ
”ˆ•GwjiGˆ•‹G›ŒG“•ŒG“›Œ™U
h™ŒG›ŒGŠ–••ŒŠ›–™šG“––šŒG–™
‹šŠ–••ŒŠ›Œ‹fG

yŒŠ–••ŒŠ›G–™
yŒ—ˆ™
›ŒGŠ–••ŒŠ›–™

jŒŠ’G›ŒGŠ–••ŒŠ›–™š
‰Œ›žŒŒ•G›ŒG”ˆ•GwjiGˆ•‹
›ŒG‹š—“ˆ GwjiUGGh™ŒG›Œ
Š–••ŒŠ›–™šG“––šŒG–™
‹šŠ–••ŒŠ›Œ‹f

yŒ—“ˆŠŒG›ŒG”ˆ•GwjiU

yŒ—“ˆŠŒG›Œ
”ˆ•GwjiU

Remove the
transit bolts
and Base
packing.

Is the washer installed on a
solidly constructed floor?

Have all the transit bolts
and base packing been
removed?

Move the
washer or
reinforce the
floor.

Check the
vibration
Sensor.

Check if the washer is
perfectly level as follows:

Check the leveling of the
washer with a level and
check that the washer is
stable.

Put an unbalance part
(rubber) inside of drum
and start QC test mode and
run in high spin.

(Refer to section 7-2.)

When the machine is
spinning in high speed,
verify that it is stable.

If you do not have the
unbalance part, put 4.5 to
6.5 lbs (2 to 3 kg) of
clothing. Once loaded,
press power, Rinse+Spin
and the start/pause button
in sequence.
When the machine is
spinning in high speed,
verify that it is stable.

If it is not stable, adjust feet
accordingly. After the
washer is level, tighten the
lock nuts up against of the
base of the washer. All lock
nuts must be tightened.

Base Packing

Unbalance Part

Refer to 
NO WATER SUPPLY

Check the wiring.

Clean the dispenser.

Put the detergent in the
correct place. 

Is water supplied?

Is the detergent caked or hardened?

Are receptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?

Has detergent been put in the correct
compartment of the dispenser?