DOWNLOAD LG WM2601HW Service Manual ↓ Size: 8.91 MB | Pages: 68 in PDF or view online for FREE

2-5. THE DOOR CAN NOT BE OPENED

While program is operating.

When a power failed and power plug is taken out in operation.

While Door Lock lights turn on.

White the motor is in the process of intertial rotating, through the operation is paused.

2-6. DOOR LOCKED LAMP LIGHTS

When the frequency of water level is lower than 22.9 kHz.

(It can be canceled when the frequency is more than 23.8 kHz.)

When the temperature inside the tub is higher than 45°C and water level is not 25.5 kHz.

(It can be canceled when the water level is 25.5 kHz or the temperature inside the tub is lower than 40°C.)

2-7. CHILD LOCK

Use this option to prevent unwanted use of the washer. Press and hold PRE WASH button for 3

seconds to lock/unlock control.

When child lock is set, CHILD LOCK lights and all buttons are disabled except the Power      button.

You can lock the controls of the washer while washing.

2-8. WATER CIRCULATION

When washing and rinsing function of shower at the upper part of Gasket.

When washing, it continuously operates for 3 minutes and intermittently.

When rinsing, it continuously operates after completion of water supply.

2-9. STEAM

For tough stained clothes, sick room linens, or baby clothes.

Steam Wash is available with Sanitary, Bulk/Large, Perm. Press, Cotton/Normal, and Baby Wear cycles.

This option features upgraded washing performance with low energy and water consumption.

Do not load delicates such as wool, silk, and easily discolored clothes.

2-10. DRUM LIGHT

The Drum Light comes on when the Power button is pressed. It goes off when the door is closed

and the washer starts operation.

The Drum Light remains off when the door is locked.

The Drum Light can be turned on while the washer is in operation by pressing the Rinse+Spin

button for 3 seconds. The light will turn off automatically 4 minutes later.

The Drum Light comes on when the washing cycle is finished and goes off 4 minutes later.

3. PARTS IDENTIFICATION

• If the supply cord is

damaged, it must be
replaced by the
manufacturer or its
authorized service
technician in order to
avoid a hazard.

ACCESSORIES

Hot/Cold (1 each)

Hose

Wrench

Tie strap (Option)

to secure drain hose to standpipe,

inlet hose, or laundry tub

1

2

3

4

5

6

Before servicing, ask the customer what the trouble is.
Check the setup (power supply is 120 V AC, remove the transit bolts level the washer...,).
Check with the troubleshooting guide.
Plan your service method by referring to the disassembly instructions.
Service the unit.
After servicing, operate the appliance to see whether it functions correctly.

STANDARD INSTALLATION

The appliance should be installed as follows:

Remove the 4 shipping bolts
with the supplied wrench.

Do first lower side to remove
easily.

Keep the shipping bolts and
spanner for future use.
Insert the 4 caps (provided)
into the hole.

Turn clockwise to raise;
counterclockwise to lower. 

Turn the leveling feet to
adjust the appliance.

4. INSTALLATION & TEST

Keeping

Higher

Lower

Verify that the rubber washer is inside of the

valve connector.

Tighten the inlet hose securely to prevent leaks.

Install the inlet hose to correct temperature

water tap.

Otherwise, it cause drips on the drawer panel

handle and drawer panel.

HOW TO CONNECT THE INLET HOSE 

CONNECT THE DRAIN HOSE

• Make sure that the hose is not twisted.

CONNECT POWER PLUG

The end of the drain hose should be placed less than 96” from the floor.

• Avoid submerging the end of the hose.

• Connect the power plug to the wall outlet.

• Avoid connecting several electric devices, 

as doing so may cause a fire.

Hot

Cold