LG WM2601HW Service Manual ▷ View online
36
VIBRATION SENSOR CHECK
Check the
leveling of
washer,
transit bolts
and base
packing
leveling of
washer,
transit bolts
and base
packing
Yes
No
No
No
No
Is the connector connected
to vibration sensor
connected or assembled?
to vibration sensor
connected or assembled?
When you check the sensor
error during LQC mode.
Is it displayed “bs2”?
error during LQC mode.
Is it displayed “bs2”?
(Refer to 7-2)
Reconnect or
repair the
connector
repair the
connector
Replace the
vibration
sensor
vibration
sensor
Reconnect or
repair the
connector
repair the
connector
Replace the
TRANS
CABLE
TRANS
CABLE
Yes
No
Is each terminal open?
(Check the all terminal of
the vibration sensor’s
connector.
(Check the all terminal of
the vibration sensor’s
connector.
Is the connector connected
to MAIN PWB assembly
connected or assembled?
(BL2)
to MAIN PWB assembly
connected or assembled?
(BL2)
Is Electrical connection
correct?
(Refer to 9-10wiring diagram)
correct?
(Refer to 9-10wiring diagram)
Replace the MAIN PWB
ASSEMBLY
ASSEMBLY
[Note]
Chances that the cause occurs from the
main controller are very little.
Sensing part of the circuit consists of
only resistors and capacitors.
Chances that the cause occurs from the
main controller are very little.
Sensing part of the circuit consists of
only resistors and capacitors.
Yes
Yes
Yes
37
DETERGENT DOES NOT FLOW IN
Refer to
NO WATER
SUPPLY.
NO WATER
SUPPLY.
Yes
Yes
No
Has detergent been put in
the correct compartment
of the dispenser?
the correct compartment
of the dispenser?
(1) Liquid chlorine Bleach Compartment
(2) Liquid fabric Softener Compartment
(3) Prewash Compartment
(4) Main Wash Compartment
Is the detergent caked or
hardened?
hardened?
Is water supplied?
Check the
wiring.
wiring.
No
Are receptacles correctly
connected to the terminals
of the INLET VALVE
ASSEMBLY?
connected to the terminals
of the INLET VALVE
ASSEMBLY?
Put the
detergent in
the correct
place.
detergent in
the correct
place.
Clean the
dispenser.
dispenser.
Yes
Yes
No
Pre wash
Main wash
: Detergent
Prewash
Hot water
Main wash
Steam
Bleach
(1)
(4)
(3)
(2)
38
LIQUID DETERGENT/SOFTENER/
BLEACH DOES NOT FLOW IN
ABNORMAL SOUND
Is water supplied?
Yes
No
Are the plugs correctly
connected to the terminals of
the INLET VALVE
ASSEMBLY?
connected to the terminals of
the INLET VALVE
ASSEMBLY?
Is the motor bolt loosened?
Is the liquid detergent/
softener/bleach cap clogged?
softener/bleach cap clogged?
Check the
wiring on the
dispenser.
wiring on the
dispenser.
Refer to
NO WATER
SUPPLY.
NO WATER
SUPPLY.
No
Is liquid detergent/softener/
bleach put in the correct
compartment of the drawer?
bleach put in the correct
compartment of the drawer?
Put it in the
correct
compartment.
correct
compartment.
Clean the cap
and
container.
and
container.
No
Yes
Yes
Yes
Secure the
bolt.
bolt.
Is there friction noise coming
from the motor?
from the motor?
Check hall
sensor.
Replace If
defective.
Then check
stator.
Replace if
necessary.
Check rotor
for broken
magnets.
Replace rotor
if necessary.
sensor.
Replace If
defective.
Then check
stator.
Replace if
necessary.
Check rotor
for broken
magnets.
Replace rotor
if necessary.
Yes
No
Yes
(1) Liquid chlorine Bleach Compartment
(2) Liquid fabric Softener Compartment
(3) Prewash Compartment
(4) Main Wash Compartment
Prewash
Hot water
Main wash
Steam
Bleach
(1)
(4)
(3)
(2)
Bleach cap
Softener
cap
cap
Liquid detergent cap
39
9-1. FILTER ASSEMBLY (LINE FILTER)
9. COMPONENT TESTING INFORMATION
When Resistance (Ohm) checking the Component, be sure to turn the power off,
and do voltage discharge sufficiently.
and do voltage discharge sufficiently.
WARNING
Wiring
diagram
diagram
Circuit in the MAIN PWB / Wiring Diagram
Vac
MAIN PWB
ASSEMBLY
ASSEMBLY
FUSE
RD1
WH1
LI
L2
RI
CI
C2
C3
3
2
1
3
2
1
Test
points
points
and
Result
Test Points
Result
WH (1) to RD (3)
WH (3) to RD (1)
0
Ω
0
Ω
(3)
(1)
(1)
WH1
(3)
(1)
RD1
Click on the first or last page to see other WM2601HW service manuals if exist.