LG WM2020CW Service Manual ▷ View online
28
8-4. TROUBLESHOOTING ELSE
NO POWER
1. Be careful of electric shock if disconnecting parts while troubleshooting.
2. First of all, check the connection of each electrical terminal with the wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, reinsert the connectors correctly.
2. First of all, check the connection of each electrical terminal with the wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, reinsert the connectors correctly.
CAUTION
Check the
fuse or reset
the circuit
breaker
fuse or reset
the circuit
breaker
Yes
No
Is the current rating of
multi-outlet power strip
enough?
(Avoid connecting several
electric devices.)
multi-outlet power strip
enough?
(Avoid connecting several
electric devices.)
Is the supplied voltage
120V AC?(+10%, -15%)
120V AC?(+10%, -15%)
Alternate with
explanation
explanation
Yes
Yes
No
Is the connector connected
to PCB/Noise filter
disconnected or
disassembled?
to PCB/Noise filter
disconnected or
disassembled?
Reconnect
or repair
the connector
or repair
the connector
No
Replace the
MAIN PWB
ASSEMBLY
MAIN PWB
ASSEMBLY
Yes
No
Is LED on while the power
is on?
is on?
Replace the
DISPLAY
PWB
ASSEMBLY
DISPLAY
PWB
ASSEMBLY
Connecting connector
MAIN PWB~ Display PWB
No
Is three pin wire of
display PWB broken?
display PWB broken?
Main LED
29
BUTTON DOESN’T WORK
Is the connector connected
to Main PWB / Display
PWB disconnected or
disassembled?
to Main PWB / Display
PWB disconnected or
disassembled?
Reconnect or
Repair
the connector
Repair
the connector
Yes
Is the display PCB broken?
(check the buzzer sound
and LED light while push
the button.)
(check the buzzer sound
and LED light while push
the button.)
Replace the
DISPLAY
PWB
ASSEMBLY
DISPLAY
PWB
ASSEMBLY
Yes
Is the button of panel stuck?
Repair the
button
button
Yes
No
No
30
VIBRATION & NOISE IN SPIN
Remove the transit bolts
and Base packing.
and Base packing.
Move the washer or
reinforce the floor.
reinforce the floor.
YES
YES
YES
NO
NO
Have all the transit bolts and base packing
been removed?
been removed?
Is the washer installed on a solidly constructed
floor?
floor?
Check if the washer is perfectly level as follows:
Check the leveling of the washer with a level
and check that the washer is stable.
and check that the washer is stable.
Put an unbalance part (rubber) inside of drum
and start QC test mode and run in high spin
(Refer to section 7-2).
When the machine is spinning in high speed,
verify that it is stable.
and start QC test mode and run in high spin
(Refer to section 7-2).
When the machine is spinning in high speed,
verify that it is stable.
If you do not have the unbalance part, put 4.5
to 6.5 lbs (2 to 3 kg) of clothing. Once loaded,
press power, Rinse+Spin and the start/pause
button in sequence.
When the machine is spinning in high speed,
verify that it is stable.
to 6.5 lbs (2 to 3 kg) of clothing. Once loaded,
press power, Rinse+Spin and the start/pause
button in sequence.
When the machine is spinning in high speed,
verify that it is stable.
If it is not stable, adjust feet accordingly. After
the washer is level, tighten the lock nuts up
against of the base of the washer. All lock nuts
must be tightened.
the washer is level, tighten the lock nuts up
against of the base of the washer. All lock nuts
must be tightened.
Adjustable feet
Adjustable feet
Lock nut
31
DETERGENT DOES NOT FLOW IN
Refer to
NO WATER SUPPLY
NO WATER SUPPLY
Check the wiring.
Clean the dispenser.
Put the detergent in the
correct place.
correct place.
YES
YES
YES
YES
NO
NO
NO
Is water supplied?
Is the detergent caked or hardened?
Are receptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?
terminals of the INLET VALVE ASSEMBLY?
Has detergent been put in the correct
compartment of the dispenser?
compartment of the dispenser?
;7.<-6-:
5)@
Click on the first or last page to see other WM2020CW service manuals if exist.