LG WM-1480FHD Service Manual ▷ View online
7
Before servicing ask the customer what the trouble is.
Check the adjustment (power supply is 220-240V~, remove the transit bolts....)
Check the troubles referring to the troubleshooting.
Decide service steps referring to disassembly instructions.
Then, service and repair.
After servicing, operate the appliance to see whether it works O K or NOT.
Check the adjustment (power supply is 220-240V~, remove the transit bolts....)
Check the troubles referring to the troubleshooting.
Decide service steps referring to disassembly instructions.
Then, service and repair.
After servicing, operate the appliance to see whether it works O K or NOT.
STANDARD INSTALLATION
The appliance should be installed as follows.
REMOVE THE TRANSIT
INSTALL THE APPLIANCE
ADJUST THE
BOLTS
ON FLAT AND FIRM SURFACE
HORIZONTAL
Remove the transit bolts
Turn the leveling feet to
(4EA: ) with supplied spanner.
set the appliance horizontally.
Keep the transit bolts and
spanner for future use.
Insert the 4 caps
provided into the hole
The appliance goes up by
rotating the feet clockwise.
The appliance comes down by
rotating the feet counter-
clockwise.
4. INSTALLATION
1
High
Low
8
HOW TO CONNECT INLET HOSE
Check that the rubber washer is inside of the
valve connector.
Connect the inlet hose firmly to prevent leak.
CONNECT DRAIN HOSE
CONNECT POWER PLUG
Make sure that the hose is not twisted.
The drain hose should be placed under 100cm from the floor.
Connect the power plug to the wall outlet.
Avoid connecting several electric devices,
It may be the cause of a fire.
Avoid submerging the end of the hose.
9
TEST OPERATION
Start/Pause
Connect the power plug to
the outlet.
In case of coloureds program.
Connect the inlet hose.
Preparation for
Press the power button.
Press the Start/Pause
washing.
button.
Press the Temp. button
Check if the drum rotates
Check if water is supplied
and the present temperature will
clockwise and counterclockwise.
through the detergent dispenser.
be displayed.
Power off and then power on.
Check if the door can be
opened after 3 minutes.
Check if the door can be
opened after 3 minutes.
Turn off Wash and Rinse after
pressing the Start/Pause button
pressing the Start/Pause button
and start the machine again.
Check drain and spin.
If SVC is needed during
check, remove
the remaining water by pulling
out the hose cap.
Check the water heating.
Check automatic reverse
Check the water supply.
turn.
Check drain and spin
Power off and open the
Water removal
door
10
5. OPERATION
LED display
Display the estimated remaining time
(Hour : Minute) to finish.
In case of abnormal operation, error
indications are displayed.
indications are displayed.
( )
See troubleshooting guide.
Wash program selector
7 program can be set depending on the type of the laundry.
If the power button is pressed, Coloureds program is
automatically set.
By turning the dial, [Coloureds
If the power button is pressed, Coloureds program is
automatically set.
By turning the dial, [Coloureds
Synthetic
Delicate
Wool
Rapid
Whites
Whites-Eco ]can be selected.
(The opposite is possible)
Start/Pause button
Use the button to start or pause wash cycle.
The power turns off automatically 4 minutes
after the pause button is pressed.
The power turns off automatically 4 minutes
after the pause button is pressed.
(Power) button
Press the button to turn power on and off.
Press the button to cancel the delay finish.
Press the button to cancel the delay finish.
Whites-Eco
If you want to get the
almost same effect as that
in 95˚C whites program with
less energy consumption,
select White-Eco program.
almost same effect as that
in 95˚C whites program with
less energy consumption,
select White-Eco program.
,
,
,
,
,
,
,
,
[WD(M)-1060F(H)D / 1065F(H)D / 1260F(H)D / 1265F(H)D / 1460F(H)D / 1465F(H)D]
Click on the first or last page to see other WM-1480FHD service manuals if exist.