DOWNLOAD LG WFW1532EK Service Manual ↓ Size: 12.79 MB | Pages: 55 in PDF or view online for FREE

36

Tub cover

Inner tub

Hub fixing nut

 

Leads

Drain Hose-p

Pump fixing screw

Remove back cover fixing screws then disassemble
the back cover.
Disconnect the leads and the drain hose-p from the
drain pump.
Remove the pump fixing screws and the connector
hose disassemble the drain pump.
Fall down the washer for clutch & motor removal.
Remove the belt.
Disassemble the clutch.
Remove two motor fixing screws then disassemble
the motor.

Separate top cover from washing machine.
As in the fig, lift snubber bar and take it out of out
case with out tub.
Damper assembly shall not be disassembled.
Replace damper as assembly.
For assembly, keep the following.(Location & color)

• To use the CHECK PROGRAM (QC TEST MODE), press WATER LEVEL, WATER TEMP. and POWER button ON

without depositing any laundry.

• In QC TEST MODE all LEDs are on and press START(PAUSE) button to check over the following items.

NO

1

CHECK METHOD

Initial state

• WATER LEVEL frequency is on

DISPLAY in the condition of no water

in TUB.

• All LEDS ON.

64~70 DISPLAY.

• Laundry amount test.

• COLD water.

• If Error of EEPROM is occured, 

is on the display

• HOT water.

• Additives Valve.

• Bleach water.

• DRAIN MOTOR is 2 st start.

• DRAIN PUMP is on.

• ALL LEDS OFF.

• RINSE water.

• if Wash capacity is 10~12KG, 

is on the display.

• if Wash capacity is 10~12KG,

is on the display

• If the LID is opened,         is on the

DISPLAY. In that case, close the LID. 

• DRAIN MOTOR is 1 st start.

• After detecting laundry amount the

number of pulse is on the DISPLAY.

• AUTO OFF.

2

Press once

3

Press twice

4

Press 3 times 

5

Press 4 times

6

Press 5 times

7

Press 6 times

8

Press 7 times

9

Press 8 times

10

Press 9 times

11

Press 10 times

DISPLAY

CHECK ITEM

38

Many washing problems involve poor soil & stain removal, residues of lint and scum, and fabric damage. For satisfactory washing
results, follow these instructions.

Poor soil
removal

Blue Stains

Black or gray
marks on
clothes

Yellow or
brown rust
stains

Lint

Residue or
Detergent

Holes, tears,
or snags

Undiluted fabric softener
dispensed directly onto fabric

A buildup caused by the interaction
of fabric softener and Detergent
can flake off and mark clothes
Not enough Detergent

Iron or manganese in water
supply, water pipes, or water
heater

Incorrect sorting
Incorrect sorting
Overloading the washer

Overloading the washer
Undissolved Detergent
Use too much Dtergent

Incorrect use of chlorine bleach.
Unfastened zippers, hooks,
buckles 
Ribs, tears and broken threads
Overloading the washer
Degradation of fabric

Not enough Detergent
Wash Water Temperaturetoo low.
Overloading the washer
Incorrect wash cycle
Incorrect sorting
Do not pretreat stain.

Use correct amount of Detergent for load size, amount of soil and
water Hardness.
Use WARM or HOT water for normal soil. Different Water Temperature
may be required according to soil type. 
Reduce load size.
Wash with Heavy or Soak & Hand Wash for heavy soiled laundry.
Separate heavily soiled items from lightly soiled ones.
Pretreat stain and heavy soil according to directions shown on
page 11.

Rub the stain with bar soap Wash.
Do not overfill fabric softener dispenser and do not pour liquid fabric
softener directly onto fabric. 
See page 14 for more instructions.

Keep the recommendations against Scrud (waxy buildup).
Use correct amount of Detergent for load size, amount of soil
and water Hardness.

To restore discolored load of whites, use rust remover safe for
fabric.
Install nonprecipitating water softener or an iron filter in your
water supply system for an ongoing problem.
Before washing, run water for a few minutes to clear lines.

Wash lint givers eg towels, flannelette sheets, separately from
lint collectors e.g. synthetic fabrics and remove tissues in
pockets before wash. See page 11 for sorting and caring before
loading.
Do not overload the washer

Do not overload the washer.
Some Detergents need to be pre-dissolved, check the
Detergent instructions. Try pre-dissolving the Detergent.
Increase Water Temperature using HOT water safe for fabric.
Use proper amount of Detergent.

Never pour chlorine bleach directly on fabric.
See page 13 for adding liquid bleach.
Fasten zippers, hooks, and buckles.
Remove objects in pockets. See page 11 for caring before loading.
Do not overload the washer.

39

For more detailed information for trouble shooting refer to page 44 to 53.

ERROR

WATER

SUPPLY &
INLET V/V

DRAINAGE

UNBALANCE

OVER

FLOODING

ERROR

WATER LEVEL
dose nto rise to
the set level in 40
minutes.

Water is not
completely
drained in 10
minutes.

Laundry
unbalance during
spin.

In the second QC
Mode the
following message
is displayed.

Water faucet is closed?
Water supply is interrupted.
Inlet V/V is clogged with
dirts.
Connector has bad contact
to the inlet valve.
Red(RD), White(WH),
Blue(BL), Yellow(YL) 3 pin
connector has bad contact to
the P.W.B ASM.

Is the drain hose located
properly?
Drain hose is not lowered.
Drain hose is folded or
clogged due to freeze or
dirts.
Bad Drain Motor part or
Yellow(YL) 3 pin  connector
to the P.W.B ASM has bad
connection.

Laundry in the INNER TUB
is filled unevenly.
Washer is tilted.
S.F S/W is too closed to the
washing tub, or has bad
contact.
Is the CONNECTOR of Ball
pressure sensor
disconnected or badly
touched?

Check INLET valve

Open water faucet.

Wait until water supply is
resumed.
Clean or replace filter.
Correct the connector
contact.

Same as above.

Hung up drain hose at
0.9~1.3m high.

Unclog the drain hose.

Replace Drain Motor or
correct the connector
contact.

Try to fill laundry uniformly
in the inner tub.

Adjust the leg.
Check and replace S.F S/W.

Check B.P SENSOR
CONNECTOR or replace
B.P sensor

ERROR DECISION

BASIS

CAUSE FOR ERROR

OCCURRENCE

REMEDY